
Two furniture-connection patents granted to Jiashan Jiarui Precision Hardware Technology Co., Ltd. solve different problems. CN213744355U expands the far end of an insert nut as the connecting rod advances. CN214837697U puts insertion members on the screw head so a second panel can cover that head. The first addresses insert retention; the second addresses the visible joint.
Neither disclosure is a load rating. A useful review starts with the load path and ends with samples made in the actual panel material.
Two different joint problems
A three-piece furniture connector usually brings a cam, a connecting rod and an insert into one joint. The insert can loosen in the panel even when the cam itself still turns. A concealed screw joint raises another question: where does the screw head go after assembly?
These patents should therefore not be ranked as two versions of the same “stronger connector.” One changes the rod-and-insert portion of a three-piece joint. The other is a Y-shaped screw that uses a second panel as part of the connection and as the cover.
That distinction also sets the test plan. Insert retention needs pull-out and repeated-assembly checks. A covered screw head needs insertion, weld and panel-damage checks as well as joint-strength tests.
The expanding insert nut
CN213744355U describes an insert nut with two opposing axial slots at the end farther from the connecting rod. The slots open into an internal threaded hole. That hole becomes narrower toward the slotted end.
As the connecting rod screws into this taper, it forces the slotted end outward against the wall of the panel hole. The design uses controlled geometric expansion to resist the insert backing out. Several tapered limiting protrusions on the outside of the nut provide additional location geometry.
The connecting rod also has a friction section with triangular projections. Their stated job is to help a person press and turn the rod by hand during installation. They should not be presented as the joint’s pull-out or anti-loosening mechanism.
Two boundaries matter here:
- The patent’s “high strength” title does not specify a material grade or a tested joint load.
- The independent claim focuses on the rod and insert nut; it is not evidence that every part of a cam-lock system has been redesigned.
For a sample review, the useful questions are concrete: What panel grade and hole diameter allow the end to expand without splitting the panel? Does the insert remain seated after repeated assembly? Does the rod still engage smoothly after that expansion?
The Y-shaped screw
CN214837697U takes a different route. Its independent claim places at least two spaced insertion members on the screw head, with features that resist their withdrawal.
The assembly sequence explains the name “traceless”:
- The screw fixes the first panel.
- The second panel is pressed or tapped onto the insertion members.
- That second panel covers the screw head.
“Traceless” describes the finished visible surface. It does not mean installation without holes, and it does not guarantee that the substrate will be free from splitting, crushing or other damage.
The dependent claims add options that should not be treated as mandatory in every version. Claim 2 describes welded insertion members. Claim 7 describes V-shaped grooves, while claim 8 describes barbs. These details create specific inspection points: weld integrity where welding is used, engagement of the grooves or barbs, and possible splitting or edge breakout when the members enter a thin panel.
Compare the joints, not the labels
| Review point | Expanding insert nut in CN213744355U | Y-shaped screw in CN214837697U |
|---|---|---|
| Main design target | Keep the insert seated in its panel hole | Join two panels while covering the screw head |
| Working geometry | A narrowing threaded hole expands the slotted far end as the rod advances | At least two insertion members on the head enter the second panel |
| Optional details to identify | Tapered external limiting protrusions; hand-installation projections on the rod | Welded members, V-shaped grooves or barbs in dependent claims |
| Main sample risks | Insert movement, panel splitting, poor thread engagement after repeated assembly | Weld failure, weak engagement, panel splitting or visible surface damage |
| Tests that need project-specific acceptance values | Pull-out, shear and repeated assembly under the intended joint conditions | Insertion, pull-out, shear and appearance under the intended panel conditions |
The table is not a performance ranking. A demountable cabinet joint and a permanently covered screw joint can be good answers to different design briefs.
What to test on real panels
Use the actual panel grade, thickness, surface layer and core material. A result from one board construction cannot be transferred to another without evidence. Keep the drilling tool, hole diameter, hole depth and insertion method in the sample record.
| Sample record | What to capture |
|---|---|
| Panel and hole preparation | Board grade and thickness, hole diameter and tolerance, drilling direction, edge distance |
| Assembly | Insertion force or method, rod engagement, visible splitting or crushing |
| Joint strength | Pull-out and shear results with the test setup and failure mode |
| Repeated assembly | Where disassembly is intended, insert movement and joint condition after the agreed cycles |
| Y-shaped screw details | Weld condition where applicable, insertion-member engagement and panel-surface damage |
For incoming-production checks, our fastener receiving inspection checklist can help separate drawing, lot and visual checks from project-specific joint tests.
ISO 7170:2021 provides test methods for the strength, durability and stability of fully assembled storage units. It does not specify acceptance values, and it is not a component-level load certification for an individual connector. Use it when the complete storage unit is the test object; define separate connector-level methods and acceptance criteria for the samples above.
Public transaction announcements from the CNIPA service window, checked on 2026-10-30, record both utility models as terminated for non-payment of annual fees. CN213744355U terminated on 2021-12-04, with the termination announced on 2022-11-11. CN214837697U was announced as terminated on 2026-07-03; the announcement did not state the effective termination date. These legal events do not establish whether a product is still made or used. The English patentee name used above follows patent-database renderings; no company-published English name was verified.
The bottom line
The expanding insert nut is a retention design. The Y-shaped screw is a joining-and-appearance design. Neither patent title replaces a test on the real panel and hole system.
References
- CN213744355U — High-strength and high-stability three-in-one connecting rod
- CN214837697U — Y-shaped traceless screw
- CNIPA service window — Chinese Patent Publication and Transaction Announcements
- ISO 7170:2021 — Furniture — Storage units — Test methods for the determination of strength, durability and stability
For a joint review, send the panel material and thickness, joint drawing, hole sizes and tolerances, expected pull-out and shear conditions, assembly-cycle requirement, appearance requirement and estimated quantity. We can help turn those inputs into a drawing review and sample-inspection plan through our project contact form.
Key Standards
Standards and clauses referenced by this article.
- Furniture — Storage units — Test methods for the determination of strength, durability and stability
Applies to fully assembled storage units; it does not specify acceptance values or certify an individual connector load.
References
Sources used for fact checking and background context.
Deep Reading
More systematic selection, procurement, or inspection guides.
- How to Choose a Fastener Supplier: A Sourcing Playbookwhitepaper
A more systematic guide on a related selection or inspection topic.
Related Solutions
Pages for specification checks and procurement discussion.
- Discuss a furniture joint review
Send panel, hole, joint and assembly details for a drawing and sample-inspection review.
- Custom Parts Review
Route drawing-based custom-part requirements.
This page is one entry in the fastener engineering reference. The library covers standards, dimensions, materials, and failure analysis; every figure is traced back to its source.
Continue reading in the library →