Engineering reference on fasteners and hardware, written by a team with manufacturing backgrounds.

About this site →

ENGINEERING TOOL

Hex Bolt Weight Chart (M6–M36) — ISO 4014 / GB/T 5782-2025

Sizes (mm)k (mm)Unit weight at 50 mm (g)
±5%
kg per 1,000 pcs (approx.)
M610412.7 g12.7
M8135.323.5 g23.5
M10166.437.9 g37.9
M12187.554.5 g54.5
M162410105 g104.8
M203012.5174 g174.5

Family index of the hex bolt weight charts: unit weight and weight per 1,000 pcs for every metric size from M6 to M36 at a 50 mm reference length, computed as geometric volume × density on carbon steel with the ISO 4014 / GB/T 5782-2025 partially threaded basis — same formula and parameters as the weight calculator and the per-size charts, ±5% estimate tolerance disclosed below the table.

Order planning

Build your bolt order list (M6–M36)

Enter size, length, material and quantity in an editable Excel workbook. Unit weights and line totals fill in automatically. Includes the full PDF and reference spreadsheet; enter your email to request the pack.

Size Index (M6–M36, at 50 mm)

Click a size for its dedicated chart (full 10–300 mm length series, material density conversion card and kg/1000 pcs ↔ lb/100 pcs toggle). s = width across flats, k = head height, pitch = coarse thread.

Sizes (mm)k (mm)Pitch (mm)Unit weight at 50 mm (g)
±5%
kg per 1,000 pcs (approx.)
M6104112.7 g12.7
M8135.31.2523.5 g23.5
M10166.41.537.9 g37.9
M12187.51.7554.5 g54.5
M14218.8276.9 g76.9
M1624102105 g104.8
M182711.52.5137 g136.7
M203012.52.5174 g174.5
M2232142.5216 g215.7
M2436153269 g268.8
M2741173368 g368.3
M304618.73.5479 g479.1
M3350213.5612 g612.3
M365522.54760 g760.4

Basis of Calculation & Disclosed Assumptions

Calculation basis

  • All values are computed as geometric volume × density (carbon steel 7.85 g/cm³, base metal, coating excluded) — identical formula and parameters as the online weight calculator and the per-size charts.
  • Hex bolt = hex head + shank + thread, on the ISO 4014 / GB/T 5782 partially threaded basis (width across flats and head height from the ISO 4014 dimension series); the thread is modelled with the mean major/minor diameter reduction, so the unthreaded portion of the shank is counted at full diameter.
  • The index column is stated at a 50 mm reference length because bolt weight scales with length; each per-size page carries the complete length series for that size.

Scope & limits

  • Theoretical geometric estimates for quotation, freight and packing budgets; use measured values for trade settlement.
  • Actual piece weight varies with thread tolerance, chamfer and coating (hot-dip galvanizing ≈ +4.5%); theoretical estimate tolerance ±5%.
  • Fully threaded bolts (ISO 4017 / GB/T 5783) carry a longer threaded portion and weigh slightly less than the partially threaded basis used here.

Need another length, material or quantity? Use the calculator

The weight calculator covers every hex bolt size with the full length series, stainless and brass density conversion, and piece / batch / pieces-per-tonne results in one pass.

Open the weight calculator

Cite this chart

YAXIIO. Hex Bolt Weight Chart (M6–M36) — ISO 4014 / GB/T 5782-2025. https://www.yaxiio.com/en/tools/bolt-weight-chart (accessed 2026-11-17).

Free to cite and embed — attribution required: “YAXIIO” + a link to this page.

FAQ

Why do the index figures use a 50 mm length?

Bolt weight grows with shank length, so a single number per size only means something with a stated length. This table uses 50 mm — the default reference length of the per-size charts. For any other length, open the size page: it lists the whole 10–300 mm series, or enter the length in the calculator.

How do I convert these carbon-steel weights to stainless, and how much does coating add?

Geometry is unchanged — only the density ratio applies: about ×1.010 for 304 and ×1.017 for 316. Coating is extra: hot-dip galvanizing typically adds 3–6%, electro zinc under 1%. All chart weights are base metal without coating.

Related References

Disclaimer: this chart provides engineering estimates for selection, quotation and freight budgeting only; it is not a design basis or an acceptance standard.