ENGINEERING TOOL
Bolt Torque Chart — Metric M6–M36 and Inch (SAE) 1/4″–2″
Metric size
Inch size
Inch (SAE Grade 2/5/8, 1/4″–2″ UNC) and metric (4.8–A4-80, M6–M36) torque tables on one page, on the same K-factor basis and the same target-preload convention, with the nearest metric size of every inch size in the same row. Every number here can be recomputed from the formula and the friction range shown below.
Full PDF
Download the full PDF (M6–M36 / 1/4"–2", all sizes)
Printable chart covering every size in this family — enter your email to get it.
Quick answer
Looking for one size only? Inch sizes 1/4″–2″ are in the first table, metric sizes M6–M36 in the second, and every size name links to its own page with five friction states, UNC and UNF.
1/2"-13 Grade 5 · dry / black (75% of proof stress) ≈ 102 N·m (92–112 N·m) · 75.2 ft·lb.
M12 class 8.8 · dry / black (70% of Rp0.2) ≈ 91 N·m (82–100 N·m) · 67.1 ft·lb.
Both lines give the typical value with its range in brackets. The range is the friction coefficient K — a band, not a point (see the K table below).
Inch (SAE) Bolt Torque — 1/4″ to 2″
UNC coarse series; typical torque at 75% of the SAE J429 proof stress with dry / black friction (K 0.18–0.22). The small line under each cell is the range across that K band.
| Inch size | Nearest metric | Grade 2 N·m | Grade 5 N·m | Grade 8 N·m |
|---|---|---|---|---|
| 1/4"UNC 20 · At 21 mm² | M6 | 7N·m (5.2 ft·lb) 7–8 | 11N·m (8.1 ft·lb) 10–13 | 16N·m (11.8 ft·lb) 15–18 |
| 5/16"UNC 18 · At 34 mm² | M8 | 15N·m (11.1 ft·lb) 14–17 | 24N·m (17.7 ft·lb) 21–26 | 33N·m (24.3 ft·lb) 30–37 |
| 3/8"UNC 16 · At 50 mm² | M10 | 27N·m (19.9 ft·lb) 24–30 | 42N·m (31 ft·lb) 38–46 | 59N·m (43.5 ft·lb) 53–65 |
| 7/16"UNC 14 · At 69 mm² | M12 | 43N·m (31.7 ft·lb) 39–48 | 67N·m (49.4 ft·lb) 60–74 | 95N·m (70.1 ft·lb) 85–104 |
| 1/2"UNC 13 · At 92 mm² | M12 | 66N·m (48.7 ft·lb) 60–73 | 102N·m (75.2 ft·lb) 92–112 | 144N·m (106 ft·lb) 130–159 |
| 9/16"UNC 12 · At 117 mm² | M14 | 95N·m (70.1 ft·lb) 86–105 | 148N·m (109 ft·lb) 133–162 | 208N·m (153 ft·lb) 187–229 |
| 5/8"UNC 11 · At 146 mm² | M16 | 132N·m (97.4 ft·lb) 119–145 | 204N·m (150 ft·lb) 183–224 | 288N·m (212 ft·lb) 259–316 |
| 3/4"UNC 10 · At 216 mm² | M20 | 234N·m (173 ft·lb) 210–257 | 361N·m (266 ft·lb) 325–397 | 510N·m (376 ft·lb) 459–561 |
| 7/8"UNC 9 · At 298 mm² | M22 | 226N·m (167 ft·lb) 204–249 | 582N·m (429 ft·lb) 524–641 | 822N·m (606 ft·lb) 740–904 |
| 1"UNC 8 · At 391 mm² | M24 | 339N·m (250 ft·lb) 305–373 | 873N·m (644 ft·lb) 785–960 | 1232N·m (909 ft·lb) 1109–1355 |
| 1-1/8"UNC 7 · At 493 mm² | M30 | 481N·m (355 ft·lb) 432–529 | 1078N·m (795 ft·lb) 970–1185 | 1747N·m (1289 ft·lb) 1573–1922 |
| 1-1/4"UNC 7 · At 625 mm² | M33 | 677N·m (499 ft·lb) 610–745 | 1519N·m (1120 ft·lb) 1367–1671 | 2464N·m (1817 ft·lb) 2217–2710 |
| 1-1/2"UNC 6 · At 907 mm² | M36 | 1179N·m (870 ft·lb) 1061–1297 | 2644N·m (1950 ft·lb) 2379–2908 | 4287N·m (3162 ft·lb) 3858–4716 |
| 2"UNC 4.5 · At 1612 mm² | — | 2794N·m (2061 ft·lb) 2515–3074 | 6266N·m (4622 ft·lb) 5640–6893 | 7621N·m (5621 ft·lb) 6859–8383 |
Cell shows the typical value with the other unit in brackets; the small line below is the range (min–max).
The nearest metric column is an order-of-magnitude comparison, not an equivalence: the two systems specify different diameters and thread forms, so a torque value must not be carried from one column to the other.
Metric Bolt Torque — M6 to M36
Typical torque at 70% of Rp0.2 with dry / black friction (K 0.18–0.22). The small line under each cell is the range across that K band.
| Metric size | 4.8 N·m | 8.8 N·m | 10.9 N·m | 12.9 N·m | A2-70 N·m | A4-80 N·m |
|---|---|---|---|---|---|---|
| M6As 20.1 mm² | 6N·m (4.4 ft·lb) 5–6 | 11N·m (8.1 ft·lb) 10–12 | 16N·m (11.8 ft·lb) 14–17 | 19N·m (14 ft·lb) 17–20 | 8N·m (5.9 ft·lb) 7–8 | 10N·m (7.4 ft·lb) 9–11 |
| M8As 36.6 mm² | 14N·m (10.3 ft·lb) 13–15 | 26N·m (19.2 ft·lb) 24–29 | 39N·m (28.8 ft·lb) 35–42 | 45N·m (33.2 ft·lb) 41–50 | 18N·m (13.3 ft·lb) 17–20 | 25N·m (18.4 ft·lb) 22–27 |
| M10As 58 mm² | 28N·m (20.7 ft·lb) 25–30 | 52N·m (38.4 ft·lb) 47–57 | 76N·m (56.1 ft·lb) 69–84 | 89N·m (65.6 ft·lb) 80–98 | 37N·m (27.3 ft·lb) 33–40 | 49N·m (36.1 ft·lb) 44–54 |
| M12As 84.3 mm² | 48N·m (35.4 ft·lb) 43–53 | 91N·m (67.1 ft·lb) 82–100 | 133N·m (98.1 ft·lb) 120–146 | 156N·m (115 ft·lb) 140–171 | 64N·m (47.2 ft·lb) 57–70 | 85N·m (62.7 ft·lb) 76–93 |
| M14As 115 mm² | 77N·m (56.8 ft·lb) 69–84 | 144N·m (106 ft·lb) 130–159 | 212N·m (156 ft·lb) 191–233 | 248N·m (183 ft·lb) 223–273 | 101N·m (74.5 ft·lb) 91–112 | 135N·m (99.6 ft·lb) 122–149 |
| M16As 157 mm² | 120N·m (88.5 ft·lb) 108–132 | 225N·m (166 ft·lb) 203–248 | 331N·m (244 ft·lb) 298–364 | 387N·m (285 ft·lb) 348–426 | 158N·m (117 ft·lb) 142–174 | 211N·m (156 ft·lb) 190–232 |
| M18As 192 mm² | 165N·m (122 ft·lb) 148–181 | 310N·m (229 ft·lb) 279–341 | 455N·m (336 ft·lb) 409–500 | 532N·m (392 ft·lb) 479–585 | 218N·m (161 ft·lb) 196–240 | 290N·m (214 ft·lb) 261–319 |
| M20As 245 mm² | 233N·m (172 ft·lb) 210–257 | 439N·m (324 ft·lb) 395–483 | 645N·m (476 ft·lb) 580–709 | 755N·m (557 ft·lb) 679–830 | 309N·m (228 ft·lb) 278–340 | 412N·m (304 ft·lb) 370–453 |
| M22As 303 mm² | 317N·m (234 ft·lb) 286–349 | 597N·m (440 ft·lb) 538–657 | 877N·m (647 ft·lb) 790–965 | 1027N·m (757 ft·lb) 924–1129 | 420N·m (310 ft·lb) 378–462 | 560N·m (413 ft·lb) 504–616 |
| M24As 353 mm² | 403N·m (297 ft·lb) 363–444 | 759N·m (560 ft·lb) 683–835 | 1115N·m (822 ft·lb) 1003–1226 | 1305N·m (963 ft·lb) 1174–1435 | 534N·m (394 ft·lb) 480–587 | 712N·m (525 ft·lb) 640–783 |
| M27As 459 mm² | 590N·m (435 ft·lb) 531–649 | 1110N·m (819 ft·lb) 999–1221 | 1631N·m (1203 ft·lb) 1468–1794 | 1909N·m (1408 ft·lb) 1718–2099 | 781N·m (576 ft·lb) 703–859 | 1041N·m (768 ft·lb) 937–1145 |
| M30As 561 mm² | 801N·m (591 ft·lb) 721–881 | 1508N·m (1112 ft·lb) 1357–1659 | 2215N·m (1634 ft·lb) 1993–2436 | 2592N·m (1912 ft·lb) 2333–2851 | 1060N·m (782 ft·lb) 954–1166 | 1414N·m (1043 ft·lb) 1272–1555 |
| M33As 694 mm² | 1090N·m (804 ft·lb) 981–1199 | 2052N·m (1513 ft·lb) 1847–2257 | 3014N·m (2223 ft·lb) 2713–3315 | 3527N·m (2601 ft·lb) 3174–3880 | 1443N·m (1064 ft·lb) 1299–1587 | 1924N·m (1419 ft·lb) 1731–2116 |
| M36As 817 mm² | 1400N·m (1033 ft·lb) 1260–1540 | 2635N·m (1943 ft·lb) 2372–2899 | 3871N·m (2855 ft·lb) 3484–4258 | 4529N·m (3340 ft·lb) 4077–4982 | 1853N·m (1367 ft·lb) 1668–2038 | 2471N·m (1823 ft·lb) 2224–2718 |
Cell shows the typical value with the other unit in brackets; the small line below is the range (min–max).
Class 8.8 is the usual default for general connections. A2-70 and A4-80 are stainless and gall easily, so use the anti-seize friction band (K≈0.10) rather than the dry / black values shown here.
Grades, Preload Levels and Friction
The two tables above hold one friction state fixed so that inch and metric can be read side by side. Everything that moves a torque value — property class, preload level and friction — is disclosed here.
SAE Grade ↔ ISO Property Class
| SAE J429 | Approx. ISO 898-1 |
|---|---|
| Grade 2 | 4.8 |
| Grade 5 | 8.8 |
| Grade 8 | 10.9 |
Approximate only: the proof stresses are not equal even where the strength bands line up (Grade 5 sits near ISO 8.8, but each standard publishes its own proof value).
75% vs 90% of Proof Stress (Inch) · 70% of Rp0.2 (Metric)
Two preload levels are in common use. The standard level — 75% of the SAE J429 proof stress for inch sizes, 70% of Rp0.2 for metric classes — is reusable and can be re-torqued. The 90% proof level sits close to yield and is a one-time setting for permanent joints with a controlled assembly method. Both percentages are of the proof (or yield) stress, not of the tensile strength, and each size page shows both levels for its own size.
Nut Factor K — Six Friction States, Full Range
K is the nut factor in T = K · d · F. It is an empirical band rather than a constant: the same bolt reaches the same preload at a different torque depending on coating, lubrication, washers and reuse. The values below are the ranges this site uses everywhere.
| Friction state | K min | K typ | K max |
|---|---|---|---|
| Dry / Black | 0.18 | 0.2 | 0.22 |
| Electro zinc | 0.15 | 0.17 | 0.2 |
| Hot-dip galvanized | 0.18 | 0.22 | 0.25 |
| Oiled | 0.12 | 0.13 | 0.15 |
| Greased / MoS₂ | 0.1 | 0.11 | 0.12 |
| Wax / PTFE / Anti-seize | 0.08 | 0.1 | 0.12 |
To move between friction states, scale the torque by the ratio of the K values — the preload stays the same. The dry / black row is the one used in the two tables above. A single precise K can only come from testing the production coating, lubrication and washer stack.
Fine Threads (UNF) and the Missing Series
Both tables above are UNC coarse threads. UNF fine-thread values are on each size page, calculated independently from the same formula: a finer thread leaves more metal at the minor diameter, so the stress area and the torque at the same grade are higher. 2" has no UNF series in ASME B1.1 (the fine series stops at 1-1/2″), so that size page shows UNC only — a UNF column there would silently reuse the coarse pitch.
Calculation basis
- T = K · d · F. F is the target preload: 75% of the SAE J429 proof stress for inch sizes (proof stress per the published J429 values, which step down by nominal-diameter tier) and 70% of Rp0.2 for metric classes (ISO 898-1 for carbon and alloy steel, ISO 3506-1 for A2/A4).
- The inch stress area follows At = π/4·(d − 0.9743/n)² (ASME B1.1); metric uses As per ISO 898-1.
- Each size name carries its own stress area, so any cell above can be recomputed from the formula and the K table.
Scope & limits
- These are simplified K-factor estimates, not a full VDI 2230 analysis (joint resilience, embedment and assembly method are not modelled).
- Friction is the dominant variable — no single torque value exists for a size without its friction state.
- Production joints follow the design specification or the manufacturer's torque table.
References
- SAE J429 — Mechanical and Material Requirements for Externally Threaded Fasteners (published grade proof stresses)
- ASME B1.1 — Unified Inch Screw Threads (tensile stress area formula)
- ISO 898-1:2013 — Mechanical properties of fasteners made of carbon and alloy steel (Rp0.2 by property class)
- ISO 3506-1:2020 — Mechanical properties of corrosion-resistant stainless steel fasteners (A2/A4)
- Machinery's Handbook — SAE J429 proof stress tiers and empirical K-factor ranges
- ISO 16047:2005 — Fasteners: torque/clamp force testing (K-factor measurement method)
- Machine Design — anti-seize compound friction test (K≈0.10)
Cite this chart
YAXIIO. Bolt Torque Chart — Metric M6–M36 and Inch (SAE) 1/4″–2″. https://www.yaxiio.com/en/tools/bolt-torque-chart (accessed 2026-11-17).
Free to cite and embed — attribution required: “YAXIIO” + a link to this page.
FAQ
Why is every value given as a range instead of one number?
Because K itself is a range: 102 N·m (92–112 N·m) · 75.2 ft·lb covers K 0.18–0.22 at one and the same target preload. Any single recommended torque figure implies one friction state, and that state is what has to be fixed first.
Do these tables cover UNC and UNF?
They cover UNC coarse threads for all 14 inch sizes; UNF fine-thread values are on each size page. 2" has no UNF series in ASME B1.1, so that page shows UNC only.
Next: work out your order, or pick the size by standard
Related References
Bolt Torque Calculator
Interactive version: product type, size, class, thread series and friction state, plus imperial UNC/UNF, stud bolts and a custom measured K.
Stud Bolt Torque Chart
Stud bolts are threaded at both ends and have no head to grip, so the tightening basis differs from a hex bolt — three nut factors side by side.
Hex Bolt Weight Chart
Per-piece and per-1,000-pcs weights across the full length series, for quoting and freight.
Tap Drill Chart for the Same Thread
The hole is drilled before the bolt is torqued: the tap drill for the thread being tightened and the nearest drill bit in the set, metric and inch side by side.
Hex Nut Weight Chart (M6–M36)
The mating nut side of the same bolted joint: hex nut unit weight and kg per 1,000 pcs for every size, each size linked to its own page.
Property Classes 4.8–12.9: What the Numbers Mean
Reads the two-number class designation, the yield and tensile values it fixes, and where the nut class system sits — cited to GB/T 3098.1-2010.
Disclaimer: these tables are an engineering estimation for selection and budgeting only. They do not constitute assembly instructions or acceptance criteria.