Coating Thickness Testing for Fasteners: Measure, Judge, Record
12 min·Yaxiio Engineering Alliance

Coating Thickness Testing for Fasteners: Measure, Judge, Record

How to measure zinc coating thickness on bolts: magnetic and gravimetric methods, GB/T 13912 and GB/T 5267.1 limits, calibration, locations and records.

Why Coating Thickness Is an Acceptance Criterion

A coated fastener is accepted on two quantities at once: the corrosion protection the coating can give, and whether the part still fits. Thickness is the one measurable on a receiving dock in minutes, which is why one reading is a poor basis for a batch decision.

The first question is which coating system is on the part. Hot-dip galvanizing builds a layer in tens of micrometres; electroplating builds single digits up to about thirty, so the systems need different tables. GB/T 13912-2020 covers hot-dip galvanized steel articles (modified adoption of ISO 1461); GB/T 5267.1-2023 covers electroplated fasteners (modified adoption of ISO 4042:2022). A 12 µm electroplated bolt read against a hot-dip table would fail a compliant part; a hot-dip bolt read against an electroplated grade can pass one the hot-dip table would reject.

Acceptance uses two numbers. GB/T 13912 defines the local thickness as the arithmetic mean of the readings in one basic measurement area, and the average thickness as the mean of those local values across the sample. A batch is not accepted by finding one good spot, and it is not rejected by one thin reading inside an area whose mean is acceptable: the standard allows readings below the limit when the area mean meets it.

Thickness is also dimensional on a thread. GB/T 5267.1-2023 Annex D states that an external thread with coating thickness t gains 4t on the pitch diameter, so a 10 µm layer moves it by 40 µm. That is enough to decide whether a nut runs on. A coating that passes corrosion but closes the go gauge is still a reject.

If you are holding a batch, the salt spray and coating guide sets out the system comparison; the coating review route takes the batch data.

Magnetic Induction: The Default for Steel Fasteners

Most fasteners are steel, and on steel the default field method is magnetic induction. The probe generates a magnetic field; the ferromagnetic substrate closes it, and a non-magnetic coating such as zinc or zinc-nickel opens a gap that the instrument converts into thickness. The method is fast, non-destructive and reads the finished part.

The procedure that produces a defensible number:

  1. Confirm the substrate is ferromagnetic; austenitic stainless steel is not, and the gauge will refuse or misread.
  2. Select a probe and range covering the expected coating; a paint-film probe is not automatically suitable for 70 µm.
  3. Zero on an uncoated reference of the same substrate, or a bare part from the lot.
  4. Read at the locations the standard names, not wherever the probe sits comfortably.
  5. Average the readings in the basic area and compare the mean with the table.

For hot-dip galvanized parts, GB/T 13912-2020 §6 gives the mechanical rules. The basic measurement area is at least 10 cm², the magnetic method takes at least five readings in that area, and their arithmetic mean is the local thickness. If the principal surfaces of five or more small parts together reach 10 cm², the magnetic method can be used on that group; if not, the gravimetric method applies.

On electroplated parts, the magnetic method is applied before the sealer, topcoat or additional lubricant, because those layers add to the reading and are not part of the zinc thickness. GB/T 5267.1-2023 §6.4 states this; its Annex A puts a sealer at roughly 0.5–2 µm and a topcoat at roughly 2–10 µm. Those layers are small against a hot-dip coating but not against a 5 µm electroplated grade.

Eddy Current, X-Ray and Gravimetric Methods

GB/T 5267.1-2023 §6.4 lists five methods for the metal layer: X-ray (GB/T 16921), coulometric (GB/T 4955), metallographic (GB/T 6462), magnetic (GB/T 4956) and phase-sensitive eddy current (GB/T 31554). The table adds the gravimetric method that GB/T 13912 makes the hot-dip reference.

Method Use it for Main limitation
Magnetic induction Non-magnetic coating on ferromagnetic substrate: steel bolts, nuts, hot-dip layers Ferromagnetic substrate only; edge and curvature errors
Eddy current Non-conductive coating on non-ferrous substrate: aluminium and copper alloy parts Not a substitute for magnetic on steel
Gravimetric Stripped samples, dispute reference Destructive; needs a known area and a balance
Metallographic Any location, dispute reference for electroplated parts Destructive; section preparation skill

The gravimetric method is reserved for disputes and for parts too small for a probe. The coating is stripped from a known area, the mass loss is weighed, and the result is converted with the nominal zinc density. GB/T 13912-2020 §6 makes this the precedence method for a hot-dip argument, and the conversion density is 7.2 g/cm³.

Formula
t (µm)=w (g/m²)÷7.2

A worked example, with illustrative inputs rather than a measured batch: a coupon of 50 cm² loses 3.60 g of coating. The mass per area is 3.60 g ÷ 0.0050 m² = 720 g/m². The thickness is 720 ÷ 7.2 = 100 µm. Every intermediate value can be recomputed from the two inputs, which is why the coupon area and mass belong in the record.

For electroplated parts the reference method is different. GB/T 5267.1-2023 §6.4 names metallographic examination to GB/T 6462, not the gravimetric conversion used for hot-dip layers. Mixing the two is a common source of a wrong verdict.

Where to Measure: Thread, Head, Shank and the 10 mm Rule

The most common inspection error is a reading taken where the standard excludes it, because the method cannot see the true thickness there.

For hot-dip galvanized parts, GB/T 13912-2020 §6 excludes cut faces, the zone within 10 mm of an edge, flame-cut faces and corners. The probe field spreads sideways; near an edge or corner there is less metal to close it, so the instrument reads low. On a bolt, the end face is the practical measuring surface; the thread flanks are not, because the probe cannot seat there.

For electroplated fasteners, GB/T 5267.1-2023 §6.4 fixes the location by product type. Long bolts, screws and studs are measured at one end plane (Figure 2a). Nuts, washers, pins and rivets are measured on any plane or another suitable area (Figure 2b and 2c). Assembled washers are measured on the bearing-face surface. A lower local thickness measured outside those locations is not grounds for rejection; the standard says so directly.

When the nominal length exceeds five diameters (l > 5d), the local thickness at mid-length can be one-third to one-half lower than at the reference area. A single reading at the middle of a long bolt therefore understates the coating that the acceptance location would show. The bolt is not necessarily thin; the reading was taken in the wrong place.

Calibration and Four Error Sources

A gauge reading 42 µm on a certified 40 µm foil is not necessarily broken; it may be outside its valid substrate, curvature or range. Calibration checks the instrument against a known thickness; it does not correct a reading taken in a forbidden location.

The routine we recommend at the start and end of a shift:

  1. Zero on the bare substrate or the instrument’s zero plate.
  2. Read two foils that bracket the expected thickness: for hot-dip work, one below and one above the table value.
  3. Record the foil readings, not only the word “calibration”.
  4. Repeat at the end of the shift. A drift invalidates the readings taken in between.

Four error sources account for most bad numbers.

Curvature. A convex surface lifts the probe field away from the coating; a concave one concentrates it. Small shanks and washer faces need a probe and a correction suited to the radius, or another location.

Edge proximity. Within 10 mm of an edge the field sees less substrate. GB/T 13912 excludes that zone for hot-dip work; the same physics applies to electroplated parts.

Substrate thickness and material. A thin sheet or small part may not provide enough ferromagnetic mass. The instrument’s minimum substrate thickness is a condition of the reading, not a suggestion.

Surface profile and contact. Rough hot-dip surfaces, scale, oil or a worn probe tip change the coupling. Clean the area and use the specified probe; do not press harder to move the number.

Acceptance by GB/T 13912 and GB/T 5267.1

Acceptance starts with the system, then the part class, then the table.

For hot-dip galvanized parts, GB/T 13912-2020 Table 3 applies to parts that are not centrifuged. Table 4 applies to centrifuged parts, the normal case for threaded fasteners because spinning removes zinc from the threads.

Centrifuged threaded fasteners, Table 4: diameter above 6 mm requires local 40 µm and average 50 µm; diameter 6 mm or less requires local 20 µm and average 25 µm.

Non-centrifuged parts, Table 3, keyed on steel thickness:

Steel thickness Local minimum Average minimum
Above 6 mm 70 µm 85 µm
Over 3 mm up to 6 mm 55 µm 70 µm
1.5 mm up to 3 mm 45 µm 55 µm
Below 1.5 mm 35 µm 45 µm

The tables show why “galvanized, 50 µm” is not a specification: an M8 centrifuged bolt at 40 µm meets the local minimum under Table 4, while a 6 mm plate at 40 µm fails the 55 µm local minimum for its thickness band in Table 3.

For electroplated fasteners, GB/T 5267.1-2023 Table 10 lists nominal thickness grades of 3, 5, 8, 10, 12, 15, 20, 25 and 30 µm, and the minimum local thickness equals the nominal value at each grade. The standard also allows the thickness requirement to be replaced by a minimum neutral salt spray duration. A designation such as ZnNi/An/720h omits thickness and states 720 h to red rust, so the order has to be read as a corrosion requirement.

Identify the system, the part class and the table before comparing numbers.

One boundary belongs here. GB/T 5267.1-2023 Table 8 durations apply to the as-plated condition, tested not earlier than 24 h after plating, on barrel-plated parts with Cr(VI)-free passivation. On received parts after handling and storage the table is a starting point, not a direct acceptance value. A salt spray duration on a certificate is not automatically a thickness.

Recording the Result: A One-Page Inspection Record

A thickness number without its location, instrument and calibration is not evidence. The record we recommend fits on one page and answers what an auditor will ask six months later.

Field What to write
Batch and order Lot number, quantity, supplier
Part and standard Description, size, property class, product standard
Substrate and coating Steel; hot-dip or electroplated; grade or designation
Instrument and calibration Method, serial number, probe, foils, readings before and after
Locations and readings Sketch per Figure 2 or basic area; every reading
Result Local mean, sample average, table and limits, verdict
Sign-off Inspector initials and date

Three habits make the record survive review. Keep the raw readings, because a mean without raw data cannot be recomputed. Sketch the locations on the drawing, because “head” and “shank” are not locations. State the standard and table, because the same 40 µm means different things in Table 3 and Table 4.

Weight data for the same parts sits in the bolt weight chart and flange weight chart; it helps identify the part and prepare a gravimetric sample. For a batch that may be disputed, retain one spare part for the reference method, which is destructive.

When the Gauge and the Certificate Disagree

Disagreement usually has one of four causes, and only one is a real coating problem: the certificate reports a specification rather than a measurement; the gauge was used outside its valid location; the instrument was calibrated for another range or substrate; or the sample and lot differ.

Work through this checklist before calling the supplier:

  1. Read what the certificate states. “Zn8” or “ZnNi/An/720h” is a designation, not a measured value.
  2. Confirm the coating system; a hot-dip part checked against an electroplated grade, or the reverse, is a false conflict.
  3. Re-zero and re-check the gauge on foils. If the foil reading is outside tolerance, the gauge result is not evidence.
  4. Re-measure at the specified location, without edge, corner or thread-flank readings.
  5. Compare like with like: local mean against local minimum, sample average against average minimum.

If the numbers still differ, the standards give a reference method rather than a vote. For hot-dip parts, GB/T 13912-2020 §6 makes the gravimetric method to GB/T 13825, at 7.2 g/cm³, take precedence over magnetic readings in a dispute. For electroplated parts, GB/T 5267.1-2023 §6.4 names metallographic examination to GB/T 6462.

Record both results and the method that resolved them. Do not average a gauge reading and a certificate value; they are not the same kind of quantity. If the reference method confirms the gauge, the certificate or the sampling is the problem. If it confirms the certificate, the gauge, its calibration or its location is.

The review pays for itself here: send the batch data, the coating designation and the readings through the coating review route.

Frequently Asked Questions

Can I measure galvanized coating with a paint thickness gauge?

The principle can be the same, but the range, probe and calibration may not be. Hot-dip layers are tens of micrometres, so check the instrument with foils that bracket that band.

How many readings do I need on one bolt?

Under GB/T 13912-2020, at least five readings in a basic area of at least 10 cm², with the mean as the local thickness. Under GB/T 5267.1-2023, the location is fixed by product type in Figure 2, and the order or product standard sets the sampling. For parts too small for a probe, use the gravimetric method.

Is thickness interchangeable with salt spray hours?

Not directly. Table 8 gives minimum durations for specific systems, thicknesses and conditions, and its footnote says a duration is not a direct basis for corrosion performance in every service environment. The thickness requirement can, however, be replaced by a minimum duration in the designation, such as ZnNi/An/720h; the inspection plan then tests that requirement instead of a thickness.

References

Key Standards

Standards and clauses referenced by this article.

  1. Metallic coatings - Hot-dip galvanized coatings on fabricated iron and steel articles§6; Tables 3 and 4

    Governing standard for hot-dip galvanized fasteners and steel articles; modified adoption of ISO 1461. Source for the basic measurement area, five-reading rule, edge exclusions, gravimetric precedence and the local/average thickness limits quoted in the text.

  2. Fasteners - Electroplated coatings§6.4; Table 8; Table 10; Annex D

    Governing standard for electroplated fasteners; modified adoption of ISO 4042:2022. Source for the measurement locations, method list, thickness grades, neutral salt spray alternative, metallographic dispute method and the 4t pitch-diameter change.

  3. Non-magnetic coatings on magnetic substrates - Measurement of coating thickness - Magnetic method

    Method standard named for magnetic induction measurement.

  4. Non-conductive coatings on non-magnetic substrates - Measurement of coating thickness - Phase-sensitive eddy current method

    Method standard named for eddy current measurement.

  5. Metallic coatings - Measurement of coating thickness - X-ray spectrometric method

    Method standard named for X-ray measurement.

  6. Metallic coatings - Measurement of coating thickness - Coulometric method

    Method standard named for coulometric measurement; not applicable when an additional non-conductive layer is present.

  7. Metallic and oxide coatings - Measurement of coating thickness - Microscopical method

    Metallographic reference method named for disputes on electroplated parts.

  8. Metallic coatings - Gravimetric determination of mass per unit area

    Gravimetric reference method named for hot-dip coating disputes; mass per area is converted at 7.2 g/cm3.

References

Sources used for fact checking and background context.

  1. ISO 1461 - Hot dip galvanized coatings on fabricated iron and steel articlesISO
  2. ISO 4042:2022 - Fasteners - Electroplated coating systemsISO
  3. National Public Service Platform for Standards Information (openstd.samr.gov.cn)State Administration for Market Regulation

Deep Reading

More systematic selection, procurement, or inspection guides.

This page is one entry in the fastener engineering reference. The library covers standards, dimensions, materials, and failure analysis; every figure is traced back to its source.

Continue reading in the library →