
Three reverse-circulation patents granted to Changsha Heijingang Industrial Co., Ltd. address three different design tasks. CN111395951B routes cuttings through a shared large-diameter base containing multiple impact units. CN113389485B removes the inner cylinder from an RC hammer while retaining the collection tube. CN114016897B spaces RC sub-hammers around an annular core-drilling body.
These are architecture choices, not field-performance results. The useful procurement question is whether air supply, pressure loss, cuttings return, sample quality and maintenance records support the intended design in the actual ground conditions.
Start with the return path
ASTM D5781/D5781M-18(2025), §1.1 defines reverse circulation for dual-wall drilling as fluid forced down the annular space between the double-wall drill pipe, while soil, sediment and rock particles return to the surface through the inner pipe.
That definition fixes the flow direction used in this article. It does not certify a hammer, a sample-recovery percentage or a penetration rate. The standard’s scope is geoenvironmental exploration and the installation of subsurface water-quality monitoring devices, so it should not be stretched into a performance approval for every mining or construction RC system.
The term also appears in oilfield drilling with different equipment and project context. For the three patents below, keep the discussion on dual-wall RC flow and the hammer’s internal return passages.
Large-diameter cuttings return
CN111395951B places at least two impact assemblies in a common base. Each assembly includes a DTH impact unit and a detachable bit. Using several impact units is not, by itself, the distinguishing point; bundled-hammer systems were already known.
The detail worth examining is the return-path geometry inside this particular base. Each impact unit has a second central hole. Air grooves connect those holes to a cuttings-discharge groove in the base. A curved section of each groove lies between adjacent bits, and the patent specifies that curved section as an arc.
The claimed combination is therefore:
multiple impact units + a shared base + arc-shaped grooves between adjacent bits + an internal cuttings-discharge passage.
It is more precise to call this an internal return channel than to imply that every flow path is a single straight central tube. For a design review, ask how air is divided between impact units, how the grooves resist blockage, how worn units are replaced and how the complete assembly is checked for pressure loss.
The patent discusses holes of 500–800 mm and above 1000 mm. Those are applicant-stated application ranges, not a continuous 500–1000+ mm rating and not project acceptance records.
The no-inner-cylinder hammer
CN113389485B removes the inner cylinder, not the collection tube. That distinction matters: the cuttings or sample passage remains, while one cylindrical component around the piston is eliminated.
In the claimed structure, the piston surrounds the collection tube. Sealing structures between the air-distribution rod and the collection tube, and between the air-distribution rod and the joint, prevent pressure release. The working chambers are bounded by the outer cylinder and the two ends of the piston; pressure changes in those chambers drive the piston back and forth.
The patent’s design intent is to reduce the part count and airflow resistance associated with an inner-cylinder arrangement. The disclosure does not supply a comparative pressure-drop curve, impact-energy result or service-life test.
A buyer should also avoid treating “fewer parts” as a maintenance conclusion before seeing the actual bill of materials. Seal wear, collection-tube wear, piston guidance and the field replacement procedure can determine whether the simpler section drawing remains simpler in service.
An annular core-drilling layout
CN114016897B uses multiple RC sub-hammers for a different objective: forming a large-diameter core. The bottom of the core-hammer barrel is annular, and the sub-hammers are spaced around that ring. As the ring of hammers cuts, the central core enters the barrel.
This is not merely another way to bundle hammers for full-face drilling. The annular body and the open centre define a coring architecture. The return and collection components must support both cuttings removal and recovery of the central core.
The patent discusses large-diameter hard-rock drilling, but it does not establish a core-recovery percentage, penetration rate or bit-life improvement. Those outcomes depend on the complete tool, ground conditions and operating record.
For an RFQ, state the required hole and core dimensions, core length, expected rock formation and acceptable recovery. Also ask how individual sub-hammers are serviced and how the barrel and core are retrieved after a blockage or unfinished run.
What the patents do not prove
A patent can establish that a particular combination of parts was disclosed. It cannot establish that the same combination is used in a current product, that it is in volume production or that it meets a project’s drilling target.
The diameter statements need the same care. Independent research has reported field work with a 665 mm RC bit in another large-diameter system, so it would be wrong to dismiss the entire 500–800 mm range as unvalidated technology. In the sources reviewed for this article, we did not find independent field validation for CN111395951B’s statement about holes above 1000 mm. That is a search boundary, not proof that no such work exists.
The same evidence rule applies to all three designs:
| Patent statement or drawing | Evidence still needed for a project decision |
|---|---|
| Multiple impact units and internal return grooves | Patent-to-model mapping, assembly drawing, air distribution and pressure-drop records |
| No inner cylinder | Actual parts list, comparative pressure loss, impact performance and wear records |
| Annular sub-hammer layout | Core dimensions, recovery results, sub-hammer service procedure and field run records |
Public transaction announcements from the CNIPA service window, checked on 2026-10-30, show that all three patents were granted in 2024 and contain no announcement of termination, voluntary abandonment or invalidation. That is not a current-rights conclusion: annual-fee records and a patent register extract were not obtained. Google Patents separately labels all three B publications Active, but that is an aggregated status rather than a CNIPA legal conclusion. For a current-rights decision, obtain a CNIPA patent register extract. Legal status does not answer the engineering questions above.
Evidence to request before RFQ
Request results under stated conditions rather than isolated maximum values. A compressor nameplate, a hole diameter or a recovery percentage cannot be compared fairly without the rest of the setup.
| Evidence area | What to request |
|---|---|
| Air supply and pressure loss | Compressor pressure and delivered flow at the tool, plus pressure drop across the hammer under the stated operating condition |
| Drilling response | Hole diameter and depth, geology, penetration rate and the test or project record that supports it |
| Cuttings return | Return continuity, blockage observations and the conditions under which return deteriorates |
| Sampling or coring | Sample recovery and contamination protocol, or core dimensions and recovery, according to the task |
| Wear and service life | Bit life and wear-part life with operating hours, metres drilled and ground conditions |
| Maintenance | Actual bill of materials, required tools, replacement procedure and recorded service time |
| Product identity | Current model, drawing revision and the relationship between the quoted tool and the cited patent |
This checklist is our procurement-review framework, not a set of thresholds from the patents. Acceptance values should be agreed for the project before comparing offers.
Match the architecture to the task
For a large full-face hole, examine the shared-base impact units and the internal grooves that collect cuttings. For a single-hammer RC design, examine what removing the inner cylinder changes in sealing, wear and pressure loss. For large-diameter coring, examine the annular sub-hammer layout together with core recovery and retrieval.
The patent helps identify which questions belong on the RFQ. It does not supply the answers.
References
- CN111395951B — Large-diameter reverse-circulation impact system
- CN113389485B — Reverse-circulation impact hammer without an inner cylinder
- CN114016897B — Reverse-circulation impact hammer and system
- CNIPA service window — Chinese Patent Publication and Transaction Announcements
- ASTM D5781/D5781M-18(2025) — Standard Guide for Use of Dual-Wall Reverse-Circulation Drilling for Geoenvironmental Exploration and the Installation of Subsurface Water Quality Monitoring Devices, §1.1
- Design and numerical analysis of a large-diameter air reverse circulation drill bit for reverse circulation down-the-hole air hammer drilling — 665 mm field study
Send the hole diameter and depth, ground and groundwater conditions, full-face or coring objective, required sample or core recovery, compressor pressure and delivered flow, drill-rod interface and site maintenance constraints through our project contact form. We can help turn those inputs into an architecture review and a supplier evidence request.
Key Standards
Standards and clauses referenced by this article.
- Standard Guide for Use of Dual-Wall Reverse-Circulation Drilling for Geoenvironmental Exploration and the Installation of Subsurface Water Quality Monitoring Devices§1.1
Defines dual-wall reverse-circulation flow direction; it is not a hammer performance certification.
References
Sources used for fact checking and background context.
- CN111395951B — Large-diameter reverse-circulation impact systempatent
- CN113389485B — Reverse-circulation impact hammer without an inner cylinderpatent
- CN114016897B — Reverse-circulation impact hammer and systempatent
- CNIPA service window — Chinese Patent Publication and Transaction Announcementsofficial
- Large-diameter air reverse-circulation drill-bit design and numerical analysis — 665 mm field studypaper
Deep Reading
More systematic selection, procurement, or inspection guides.
- How to Choose a Fastener Supplier: A Sourcing Playbookwhitepaper
A more systematic guide on a related selection or inspection topic.
Related Solutions
Pages for specification checks and procurement discussion.
- Discuss an RC drilling architecture review
Send ground conditions, hole dimensions, compressor delivery and full-face or coring requirements.
This page is one entry in the fastener engineering reference. The library covers standards, dimensions, materials, and failure analysis; every figure is traced back to its source.
Continue reading in the library →