Salt Spray Hours Are Not Service Years: Reading Corrosion Test Claims
30 min·Yaxiio Engineering Alliance

Salt Spray Hours Are Not Service Years: Reading Corrosion Test Claims

Salt spray test hours do not convert into service years. Read a 480 h report by test type, failure criterion and specimen state before accepting it.

What a 480-hour pass actually certifies

A supplier sends a test report. One line reads: neutral salt spray, 480 h, no red rust, qualified. The buyer’s next question is always the same. How many years is that?

The report does not answer it, and was never built to. A salt spray result is three things: a test method, a set of conditions, and a pass criterion. The hour count is the point at which someone stopped looking.

GB/T 10125-2021 is the method standard behind most reports. Its scope clause sets the boundary: the methods serve quality control and batch comparison, they are not suitable for ranking different materials by corrosion resistance, and they are not suitable for predicting long-term corrosion resistance. The same clause states that test hours cannot be converted directly into service life, and that specimen type, test period and interpretation belong to the product specification. The standard that defines how to run the test also defines what the result may not be used for.

GB/T 5267.1-2023, which sets coating requirements for electroplated fasteners, repeats the warning in Table 8 footnote a: the minimum salt spray duration is not a direct basis for corrosion resistance in all environments the fastener may meet.

480 h is not a physical threshold. GB/T 10125-2021 §11.1 lists the recommended periods as 2, 6, 24, 48, 96, 168, 240, 480, 720 and 1008 h. 480 is one rung on that ladder, picked in a contract. If another project writes 720 h for the same coating, the coating has not improved; the acceptance line has moved.

For a procurement file: 480 h certifies that a specimen survived a defined fog for 480 h under a defined criterion. It does not certify years, and no clause in GB/T 10125 supplies a conversion.

NSS, AASS and CASS are three different tests

The three methods share a salt solution and a deposition rate. The remaining conditions drive the corrosion rate.

Parameter NSS AASS CASS
Cabinet temperature 35 °C ±2 °C 35 °C ±2 °C 50 °C ±2 °C
Collected solution pH 6.5 to 7.2 3.1 to 3.3 3.1 to 3.3
Sodium chloride 50 g/L ±5 g/L 50 g/L ±5 g/L 50 g/L ±5 g/L
Copper addition none none 0.26 g/L ±0.02 g/L as CuCl2·2H2O
Deposition, 80 cm2 horizontal 1.5 mL/h ±0.5 mL/h same same
Target coatings metals, alloys and coatings; quality control and batch comparison decorative copper-nickel-chromium, nickel-chromium, anodised aluminium, organic coatings the same decorative family, accelerated further

AASS acidifies the solution with acetic acid. CASS adds copper chloride and runs at 50 °C. Both were written for decorative coating systems. A hot-dip galvanized structural bolt is not their target. A CASS report for a galvanized fastener describes conditions chosen for another coating family, and the hours do not carry over.

Cabinet history matters. A chamber used for AASS or CASS must not be used for NSS without thorough cleaning and verification. Ask which chamber ran the test; contamination shifts results in ways a one-page report will never show.

One number, different failures

GB/T 5267.1-2023 Table 8 shows the problem inside a single block of cells. For a zinc coating with a clear passivation, coded Zn//An/T0, the minimum neutral salt spray time is 8 h with no white corrosion, and 48 h, 72 h or 96 h with no red rust at 5, 8 or 12 μm of coating. Same system, same cabinet, same coupon. At 8 μm the answer to “how many hours” is 8 if the criterion is white corrosion and 72 if the criterion is red rust. Nine times the duration, because the failure being watched for changed.

Four criteria appear in fastener reports:

  • white corrosion, the zinc corrosion product, which marks the coating being consumed
  • red rust, base metal corrosion, the usual structural criterion
  • blistering, cracking and flaking, which are adhesion and barrier failures
  • scribe creep, the distance corrosion travels from a deliberate scratch

GB/T 10125-2021 §13 lets the evaluation be any of: appearance after the test, appearance after removal of corrosion products, number and distribution of defects (pitting, cracks, blistering, rust, scribe creep), time to first corrosion, mass change, microstructure, or mechanical properties, with ratings taken from GB/T 6461, ISO 8993 and the GB/T 30789 series. A report should name the one it used. “Pass” with no named criterion cannot be compared with anything.

A scribed coupon answers a different question from an unscribed one. The scratch exposes bare steel, so the test measures lateral growth at a damaged edge; an unscribed coupon measures the barrier of an intact coating. A report that omits the detail leaves the hour count open to two readings.

Table 8 also carries boundary conditions reports tend to drop. The values apply to the coating state, tested at least 24 h after plating, on barrel-plated parts without hexavalent chromium passivation. Received-state parts, rack plating and chromate systems sit outside the table. The footnotes add that white haze is not white corrosion and that black spots are not a rejection reason.

Setup choices that move the result

Some variables are fixed by the standard, some by the laboratory. Both change the number.

  • Angle: specimens sit 15° to 25° from vertical, preferably 20°; repositioning is allowed when the total period exceeds 96 h.
  • Handling after test: indoor air dry for 0.5 to 1 h, rinse in clean running water at 40 °C or below, blow dry from about 300 mm at 200 kPa or less.
  • Salt quality: heavy metals below 0.005% in total, sodium iodide at 0.1% or less, total impurities at 0.5% or less. Anti-caking agents can accelerate or inhibit corrosion.
  • Chamber verification: steel reference coupons, at least four, ISO 3574 CR4, 150 × 70 × 1.0 mm, Ra 0.8 ±0.3 μm, inclined at 20° ±5°. For NSS at 48 h the mass loss should be 70 g/m² ±20. The suggested interval is about three months.

The last item is the one to request. A report from a chamber with current reference-coupon records differs from one without them, even at the same 480 h.

Why hours do not scale into years

Corrosion outdoors is driven by time of wetness, chloride deposition, temperature cycling and sulphur dioxide. The salt fog holds all four constant and extreme: continuous wet, 35 °C, 50 g/L sodium chloride, no drying cycle. A structure in service spends most of its life dry. The acceleration factor linking the two depends on the coating, the site and the season. It is not a constant waiting in a table.

GB/T 18226-2025, the Chinese standard for highway steel component anti-corrosion, shows how a standard uses salt spray hours. Annex A sorts environments into JC3 (urban and industrial atmosphere, moderate sulphur dioxide, low-salinity coast), JC4 (industrial areas and medium-salinity coast), JC5 (high humidity, severe industrial atmosphere, high-salinity coast) and JCX (offshore and extreme tropical industrial zones). Table A.2 then requires coating systems to reach 1000 h of salt spray at JC3, 2000 h at JC4, 3000 h at JC5 and 4000 h at JCX.

Read that ladder for what it is: an acceptance schedule that steps up with the environment, not a measurement of how fast each environment eats a coating. Table A.2 gives durations, not a factor between classes; it does not state that a JC5 coating lasts one third as long as a JC3 coating. The 1:2:3:4 progression is a convention.

The same reasoning applies to the C3 and C5 atmospheric corrosivity categories of ISO 9223. A coating exposed at C5 is consumed faster than the same coating at C3. That sentence is safe. Any number attached to it depends on chloride deposition, rainfall, sheltering and the coating itself, and cannot be derived from salt spray hours. If a supplier offers a conversion, ask for the exposure data behind it.

What the number supports: within one coating system and one criterion, a longer survival time means the coating resisted that test longer. It does not mean proportionally longer service.

What salt spray hours are good for

Same-condition comparison. Hold the method, standard version, test type, criterion, specimen state and thickness constant, and the hours rank suppliers, batches or process changes. That is the use the scope clause permits.

Change one variable and the ranking collapses. Two reports both saying “480 h, no red rust” can describe coatings with very different margins. Per GB/T 5267.1-2023 Table 8, a Zn//Cn/T2 system at 8 μm must reach 240 h without red rust, while a Zn//An/T0 system at 12 μm must reach 96 h. A 480 h result is twice the requirement in the first case and five times the requirement in the second. The report line is identical; what it says is not.

Compare against the requirement, not against another supplier’s headline. The same 480 h is generous when the contract asked for 240 h and thin when it asked for 1008 h.

Evidence that supports a service claim

Salt spray is a screening test. For service life, other evidence carries more weight.

Cyclic corrosion testing alternates salt fog with drying and humid phases, so the sample sees wet-dry transitions instead of permanent wetness. Ask which cycle profile ran and whether the report shows the cycle, not only a total duration.

Atmospheric exposure data is the direct evidence. Coupons are mounted on racks at a site with measured chloride deposition and sulphur dioxide, then removed at intervals for mass loss or coating thickness. One or two years at a comparable location says more about the project than any accelerated test.

Coating thickness and adhesion come next. A salt spray result without a thickness is incomplete. For hot-dip galvanized threaded parts over 6 mm in diameter, GB/T 13912-2020 Table 4 sets a local minimum of 40 μm and an average minimum of 50 μm after centrifuging; uncentrifuged steel over 6 mm is 70 μm local and 85 μm average under Table 3. Thickness sets how much zinc is available. The salt spray hours describe how a coupon surface behaved, not how a thread flank will behave after handling, tightening and abrasion. The coating and plating families reference sets the thickness ranges side by side.

Pre-treatment records close the set: degreasing, pickling, flux composition, passivation type, and for electroplated high-strength parts the baking record. A coating that passed 480 h in a laboratory can still fail in the first wet season if pre-treatment drifted between batches. On parts at 10.9 or above, the plating and baking sequence also carries a hydrogen risk, covered in the article on hydrogen embrittlement in high-strength fasteners.

Should you trust this report?

1Does the report name the standard and its version?
No
✅
Treat the hours as a marketing figure
Yes
⚠️
Check the test type next
↓
2Does the report name the test type?
No
✅
Ask which test ran; durations may not transfer
Yes
⚠️
Check the failure criterion
↓
3Is the failure criterion defined?
No
✅
Hours cannot be compared; request a reissue
Yes
⚠️
Check the specimen record
↓
4Are specimen state, thickness and laboratory named?
No
✅
Request thickness, photos and lab identity
Yes
⚠️
Usable for same-condition comparison only

Report checklist before you accept

Takeaway Checklist
Copy this checklist into your tender documents
Selected conditions
Tap to check, this is your procurement checklist

Writing hours into a purchase order

A clause saying “at least 480 h salt spray” is incomplete on five counts. Write the whole sentence:

“Neutral salt spray (NSS) to GB/T 10125-2021, 480 h minimum, no red rust, unscribed specimens, coating thickness 8 μm minimum, tested in the coating state within 24 h of plating, rated to GB/T 6461, third-party laboratory with current reference-coupon records.”

Each qualifier blocks a substitution. The version fixes periods and conditions. The test type blocks a CASS report. The criterion blocks white corrosion presented as red rust. The specimen state blocks aged parts. The thickness blocks a thin coating carried by a long duration. The laboratory requirement blocks an unverified in-house report.

GB/T 5267.1-2023 makes the thickness question sharper. In its marking system a minimum neutral salt spray duration can replace the thickness field, so a part can be ordered as ZnNi/An/720h with no thickness stated. When hours stand in for thickness, the criterion and the specimen state carry the whole meaning of the order.

If the project sits on a coast or in an industrial zone, take the duration from the environment class rather than a competitor’s datasheet. GB/T 18226-2025 Table A.2 runs from 1000 h at JC3 to 4000 h at JCX for coating systems on highway steel components. That range starts a discussion; it does not replace your product specification.

Three things to carry into the meeting

  • The hours are a duration plus a criterion, not a service life, and no clause in GB/T 10125 converts them into years.
  • Compare only within one method, one criterion, one thickness and one specimen state; outside that set the number is not comparable.
  • Ask for thickness, adhesion, pre-treatment and exposure or cyclic data when the question is how long the coating will last.

Before the inspection plan is signed, put the test report and the drawing callout side by side. A review of version, criterion and thickness usually takes one pass, and settles whether the 480 h is a specification or a sales number.

References
  • GB/T 10125-2021 — Corrosion tests in artificial atmospheres: Salt spray tests
  • GB/T 5267.1-2023 — Fasteners: Electroplated coatings, Table 8 and footnotes
  • GB/T 18226-2025 — Anti-corrosion specification for steel components of highway traffic engineering, Annex A
  • GB/T 13912-2020 — Metallic coatings: Hot dip galvanized coatings on fabricated iron and steel articles, Tables 3 and 4
  • ISO 9227:2017 — Corrosion tests in artificial atmospheres: Salt spray tests (the international source of GB/T 10125, modified adoption)
  • ISO 9223:2012 — Corrosion of metals and alloys: Corrosivity of atmospheres, classification, determination and estimation

Key Standards

Standards and clauses referenced by this article.

  1. Corrosion tests in artificial atmospheres — Salt spray tests (modified adoption of ISO 9227:2017)§1, §11.1, §13

    Test conditions for NSS, AASS and CASS; the recommended period ladder that includes 480 h; the evaluation options; and the scope statement that the methods are for quality control and batch comparison, not for ranking materials or predicting long-term corrosion resistance.

  2. Fasteners — Electroplated coatingsTable 8 and footnotes a, c, d; §9.2 (marking)

    Minimum neutral salt spray durations by coating system code and thickness, split between no white corrosion and no red rust; the footnote that the duration is not a direct basis for corrosion resistance in all environments; and the marking rule that allows a duration to replace the thickness field.

  3. Anti-corrosion specification for steel components of highway traffic engineeringAnnex A, Table A.1 and Table A.2

    Environment classes JC3 to JCX and the salt spray duration required for coating systems at each class: 1000 h, 2000 h, 3000 h and 4000 h.

  4. Metallic coatings — Hot dip galvanized coatings on fabricated iron and steel articlesTable 3 and Table 4

    Minimum local and average coating thickness for hot-dip galvanized parts, including the centrifuged threaded-part values used in the article.

References

Sources used for fact checking and background context.

  1. GB/T 10125-2021 — Corrosion tests in artificial atmospheres: Salt spray testsSAMR / SAC
  2. GB/T 5267.1-2023 — Fasteners: Electroplated coatingsSAMR / SAC
  3. GB/T 18226-2025 — Anti-corrosion specification for steel components of highway traffic engineeringSAMR / SAC
  4. ISO 9227:2017 — Corrosion tests in artificial atmospheres: Salt spray testsISO

Deep Reading

More systematic selection, procurement, or inspection guides.

This page is one entry in the fastener engineering reference. The library covers standards, dimensions, materials, and failure analysis; every figure is traced back to its source.

Continue reading in the library →