Why Are Screw Threads 60 Degrees? The Geometry Behind the Number
25 min·Yaxiio Engineering Alliance

Why Are Screw Threads 60 Degrees? The Geometry Behind the Number

A 60 degree thread angle makes the basic profile an equilateral triangle. See how H, thread depth, stress area and the three-wire constants follow, with M12 examples.

The short answer: 60° is a geometry choice

A 60° thread angle is the included angle of the basic profile shared by ISO metric (M) and Unified inch (UN) threads. FED-STD-H28/21B §1 defines the M and MJ profiles as 60°, symmetrical thread forms; the Unified UN and UNR forms in FED-STD-H28/2B use the same basic profile. The angle is a convention, and the convention leaves three numbers you can compute on paper:

  • H = 0.866025P, the height of the fundamental triangle, where P is the pitch.
  • 0.6134P, the basic height of the external thread.
  • A_s = (π/4)(d − 0.9382P)², the tensile stress area used for bolt strength.

For an M12×1.75 bolt those three lines give H = 1.5155 mm, a thread height of 1.0735 mm and a stress area of 84.3 mm². The sections below derive each number, show what the angle does to the load path, and cover the bench check.

Where the 60° comes from

The basic profile is built on an equilateral triangle whose base equals the pitch. ISO 68-1:2023 defines this basic and design profile for metric threads, and the two federal sections apply it to the M and UN families. Because the triangle is equilateral, each flank sits 30° from the perpendicular to the axis, and the height follows from the half-base:

Formula
Half-base=P/2
H=(P/2)/tan 30°=(P/2)×1.732051=0.866025P

Every other dimension is a fraction of H, so one angle serves every diameter and pitch: a single-point tool set to 60° cuts M3 or M64, and the same comparator setting checks both. The system scales linearly with pitch.

It is a convention, not an optimum. A 55° Whitworth thread and a 30° trapezoidal thread solve the same problem with a different trade-off.

The fundamental triangle in real numbers

Three quantities follow from the 60° profile.

Height. H = 0.866025P, as derived above. For P = 1.75 mm, H = 1.5155 mm.

Crest truncation. The crest is cut back by H/8 = 0.10825P, so a finished thread carries a flat on top rather than a knife edge.

External thread height. Subtract the crest truncation H/8 and the root truncation H/6 used in the basic profile from the full triangle:

Formula
h=H − H/8 − H/6=(24 − 3 − 4)H/24=17H/24=0.61343P
M12×1.75: h=0.61343×1.75=1.0735 mm

The internal thread is the same triangle cut as a nut, with the crest truncated by H/8 and the root by H/4:

Formula
h(internal)=H − H/8 − H/4=15H/24=0.625H=0.54127P

FED-STD-H28/2B §20.2.3 states that internal value directly: the basic height of the Unified profile is 0.625H. The same paragraph gives the consequence for tapped holes — because the usable height is 0.625H rather than the old 0.75H, the maximum percentage of thread is 83.3%. A hole tapped to nominal drill size is never a 100% thread.

The two heights cross-check each other, since both come from the same triangle. If your arithmetic does not land on both, a sharp-V profile has crept into the calculation.

What the flank angle does to the load

An axial load is carried by the flanks. Take one flank, neglect friction, and treat the thread as a wedge with half-angle 30°. The normal force N resolves into an axial component that balances the load and a radial component that pushes the nut outward:

Formula
N cos 30°=F → N=F/cos 30°
F_r=N sin 30°=F tan 30°=0.5774F

So every 1 kN of axial load puts about 0.577 kN of radial force on a 60° thread. Run the same wedge calculation at the other two profile angles:

Profile Included angle Half-angle Radial force per unit axial load
ISO metric / Unified 60° 30° 0.5774F
Whitworth (BS 84) 55° 27.5° 0.5206F
Trapezoidal (ISO 2901) 30° 15° 0.2679F

The 30° trapezoid produces 54% less radial force than the 60° form at the same axial load. That is why power screws use it: radial force is wasted work and extra friction on a long leadscrew. The 55° form sits between the two, 9.8% below the 60° figure.

Friction changes the magnitude but not the ranking. The wedge multiplies the friction coefficient by 1/cos(α/2): μ/cos 30° = 1.155μ at 60°, 1.128μ at 55°, 1.035μ at 30°. At μ = 0.15 that is 0.173, 0.169 and 0.155. The higher effective coefficient is what stops a fastener backing out: at ordinary lead angles the 60° form self-locks, while a trapezoidal power screw can be driven backwards and may need a brake.

Stress area: the number that sets strength

Bolt strength is not calculated on the major diameter. FED-STD-H28/2B §70.1 records the test basis: threaded parts fail at loads corresponding to an unthreaded section whose diameter is midway between the pitch and minor diameters. That definition gives A_s = (π/4)((d2 + d3)/2)².

For a 60° thread both diameters are fixed multiples of the pitch, d2 = d − 0.649519P (FED-STD-H28/21B §6.320) and d3 = d − 1.226869P, so the midpoint collapses to a single constant:

Formula
(d2+d3)/2=d − (0.649519+1.226869)P/2=d − 0.938194P
A_s=(π/4)(d − 0.9382P)²

Two worked examples on the same nominal diameter:

Formula
M12×1.75: 12 − 0.9382×1.75=10.35815 mm
A_s=0.785398×10.35815²=84.27 mm²
M12×1.25: 12 − 0.9382×1.25=10.82725 mm
A_s=0.785398×10.82725²=92.07 mm²

The fine pitch carries 9.3% more area on the same shank: 92.07 / 84.27 = 1.0926. If a handbook gives 84.3 mm² for M12 coarse and 92.1 mm² for M12 fine, this is the formula behind those rows, not a tensile test. The 0.9382 constant belongs to the 60° profile; a 55° thread has a different one, so a stress area computed with 0.9382 does not describe a Whitworth thread.

Stress area is also the input to a torque figure. The bolt torque chart lists values for M6 to M36 and SAE 1/4 to 2 in by property class; the geometry on this page tells you which area those values came from.

The numbers for M6 to M24

Coarse pitches from GB/T 5782-2025 Tables 2 and 3; every other column calculated from the basic 60° profile.

Size P (mm) H = 0.866025P (mm) External height 0.61343P (mm) Basic pitch dia d2 (mm) A_s (mm²)
M6 1.00 0.8660 0.6134 5.350 20.1
M8 1.25 1.0825 0.7668 7.188 36.6
M10 1.50 1.2990 0.9202 9.026 58.0
M12 1.75 1.5155 1.0735 10.863 84.3
M16 2.00 1.7321 1.2269 14.701 156.7
M20 2.50 2.1651 1.5336 18.376 244.8
M24 3.00 2.5981 1.8403 22.051 352.5

Thread height grows with pitch, not diameter: M24 at 3.0 mm pitch is 1.840 mm deep, three times the M6 depth, while its diameter is four times as large. A_s grows faster than d², because the pitch term d − 0.9382P pulls the effective diameter down by a larger absolute amount at coarse pitch.

Measuring the angle and the pitch diameter

Two separate checks, often confused.

Form. The flank angle is checked against a 60° setting on an optical comparator, or with a thread profile gauge. The wire method does not measure the angle. It assumes 60° flanks and solves for the pitch diameter; if the angle is wrong, the reading is computed from a false premise.

Size. The three-wire method measures across wires seated in the groove and subtracts the geometry. The best wire touches the flank at the pitch line, where the groove width equals P/2:

Formula
d_w=P/(2 cos 30°)=P/1.732051=0.57735P
Measurement over wires: M=d2+3d_w − (P/2) cot 30°
M=d2+3d_w − 0.86603P

M12×1.75 with best-size wires:

Formula
d_w=0.57735×1.75=1.010 mm
M=10.863+3(1.010) − 0.86603(1.75)
M=10.863+3.030 − 1.516=12.377 mm

If the pitch diameter is at basic size, 10.863 mm, the micrometer reads 12.377 mm over the wires. FED-STD-H28/22A §5.5 gives the same relation in words: pitch diameter approximately equals the measurement over best-size wires minus a constant. §5.4.1 sets the wire requirements — three wires within 0.00025 mm of each other, within 0.0005 mm of best size.

Use the measured wire diameter, not the printed one. A wire 0.01 mm larger than the value you use raises the calculated pitch diameter by 3 × 0.01 = 0.03 mm.

The constants belong to the angle. For a 55° Whitworth thread they become 0.5637P for the best wire and 0.9605P for the correction. At P = 1.75 mm the correction differs from the 60° value by 0.165 mm — enough to turn a conforming part into a rejected one.

Why 55° and 30° exist

Whitworth form uses a 55° included angle (BS 84:2007). A smaller angle makes the fundamental triangle taller — 0.9605P at 55° against 0.866025P at 60° for the same pitch — and cuts radial force by 9.8%. The trade is dimensional: at the same pitch the two profiles share neither depths, constants nor wires, so a 55° part and a 60° part will not assemble.

Trapezoidal threads use a 30° included angle (ISO 2901:2016). The triangle is 1.8660P tall, radial force drops 54% against the 60° form, and effective friction is 1.035μ against 1.155μ. Those changes are what a leadscrew wants: more axial travel per unit of torque, less bursting load on the nut, a wider tool. The cost is easier back-driving.

The 60° form sits in the middle of that range, and it is the angle both fastener systems standardised on. That is why metric and inch threads share constants — and why the sharing stops there.

What 60° does not let you do

It does not make M and UN interchangeable. M6 coarse pitch is 1.00 mm (GB/T 5782-2025 Table 2). A 1/4-20 UNC thread has a 0.250 in major diameter, which is 6.350 mm, and a pitch of 25.4 / 20 = 1.270 mm. Different diameter, different pitch, no fit, whatever the angle has in common. The thread system comparison covers the families in more detail.

It does not transfer the inspection constants to 55° or 30° parts. The 0.86603P and 0.57735P factors are 60° numbers. Applied to a Whitworth thread they return a pitch diameter that is wrong by 0.165 mm at a 1.75 mm pitch.

It does not set strength or acceptance on its own. Pitch sets the stress area: two M12 bolts at 1.75 and 1.25 share the angle and differ by 9.3%. And the angle defines nominal geometry only; whether a part is 6g or 6H, 2A or 2B, comes from the tolerance system on the drawing, and the wire reading is compared against that limit.

A shop-floor checklist

Takeaway Checklist
Copy this checklist into your tender documents
Selected conditions
Tap to check, this is your procurement checklist

What to send for a review

A drawing that gives only “60°” and a diameter is missing the two values that decide acceptance: the pitch (or threads per inch) and the tolerance class. Send the callout as written, the measured pitch diameter, the wire diameter used and the standard you inspect to. An engineer can review whether the part was measured against the right profile before the lot is accepted, reworked or scrapped.

References
  • FED-STD-H28/21B:1984 — Screw-Thread Standards Section 21: Metric Screw-Threads, §1 and §6.320
  • FED-STD-H28/2B:2019 — Screw-Thread Standards Section 2: Unified Inch Screw Threads, §20.2.3, §70.1
  • FED-STD-H28/22A:1991 — Gages and Gaging for Metric Screw Threads, §5.4.1, §5.5
  • GB/T 5782-2025 — Hexagon head bolts, Tables 2 and 3 (coarse pitch by size)
  • BS 84:2007 — Parallel screw threads of Whitworth form — Requirements
  • ISO 68-1:2023 — ISO general purpose screw threads — Basic and design profiles — Part 1: Metric screw threads
  • ISO 2901:2016 — ISO metric trapezoidal screw threads — Basic and design profiles

Key Standards

Standards and clauses referenced by this article.

  1. Screw-Thread Standards Section 21: Metric Screw-ThreadsU.S. Department of Defense

    Section 1 defines the M and MJ profiles as 60 degree symmetrical threads; 6.320 gives pitch diameter as d minus 0.649519P.

  2. Screw-Thread Standards Section 2: Unified Inch Screw Threads UN and UNR Thread FormsU.S. Department of Defense

    20.2.3 gives the basic Unified thread height as 0.625H and the 83.3 percent thread ceiling; 70.1 gives the stress-area basis.

  3. Screw-Thread Standards Section 22: Gages and Gaging for Metric Screw Threads M and MJU.S. Department of Defense

    5.5 relates pitch diameter to the measurement over best-size wires; 5.4.1 sets wire diameter tolerances.

  4. Fasteners: Hexagon head boltsSAMR / SAC

    Tables 2 and 3 give the coarse pitch for M5 to M24 used in the comparison table.

  5. Parallel screw threads of Whitworth form: RequirementsBritish Standards Institution

    Defines the Whitworth form used here as the 55 degree comparison.

  6. ISO general purpose screw threads: Basic and design profiles, Part 1: Metric screw threadsInternational Organization for Standardization

    Defines the basic 60 degree profile and its crest and root truncations.

References

Sources used for fact checking and background context.

  1. FED-STD-H28/21B:1984, Metric Screw-Threads, sections 1 and 6.320U.S. Department of Defense

    60 degree M and MJ profile; pitch diameter formula.

  2. FED-STD-H28/2B:2019, Unified Inch Screw Threads, sections 20.2.3 and 70.1U.S. Department of Defense

    Basic thread height 0.625H; tensile stress area basis.

  3. FED-STD-H28/22A:1991, Gages and Gaging for Metric Screw Threads, sections 5.4.1 and 5.5U.S. Department of Defense

    Best-size wire requirements and the over-wire pitch diameter relation.

  4. GB/T 5782-2025, Hexagon head bolts, Tables 2 and 3SAMR / SAC

    Coarse pitch by nominal size.

  5. BS 84:2007, Parallel screw threads of Whitworth form: RequirementsBritish Standards Institution

    Whitworth 55 degree form.

  6. ISO 68-1:2023, Basic and design profiles, Part 1: Metric screw threadsInternational Organization for Standardization

    Basic 60 degree profile and truncations.

  7. ISO 2901:2016, ISO metric trapezoidal screw threads: Basic and design profilesInternational Organization for Standardization

    30 degree trapezoidal profile.

Deep Reading

More systematic selection, procurement, or inspection guides.

This page is one entry in the fastener engineering reference. The library covers standards, dimensions, materials, and failure analysis; every figure is traced back to its source.

Continue reading in the library →