The Short Answer: Torque Only Approximates Preload
A torque value on a drawing is not a clamp force. It is a clamp force multiplied by the nominal diameter and by a coefficient nobody measured on that joint: the K factor, also called the nut factor or torque coefficient.
T is tightening torque, F is bolt preload and d is the nominal thread diameter. Set the units once and the equation is honest: N·m, kN and mm, which is the pairing GB/T 1231-2024 uses in §7.4.1. Rearranged, F = T / (K · d). Torque is what the wrench measures, diameter is on the drawing, and K is the only input that depends on the actual batch in the box.
| You have | You need | The weak link |
|---|---|---|
| A torque value from a chart | A preload estimate for this joint | K for this finish and lubricant |
| A target preload | A torque to set on the wrench | The same K, plus the basis of the preload target |
Our bolt torque calculator runs the same three inputs. If you prefer a table, read the bolt torque chart, then check the value against the method here.
T = K·D·F and the Units That Break It
The standard defines the coefficient from the test rather than from a catalogue. GB/T 1231-2024 §7.4.1 uses the single-value form:
where T is the peak tightening torque in N·m, F is the peak bolt preload in kN and d is the nominal thread diameter in mm. Kilonewtons multiplied by millimetres equal newton-metres, so the units cancel and Ki is dimensionless.
| Symbol | Meaning | Unit | Common error |
|---|---|---|---|
| T | Peak tightening torque | N·m | ft·lb left unconverted |
| F | Peak bolt preload | kN | Newtons entered in place of kilonewtons |
| d | Nominal thread diameter | mm | Stress diameter substituted |
| K | Torque coefficient | none | Treated as a constant |
The diameter is nominal, 12 mm for M12, not the stress area diameter; the two differ by more than ten percent, which moves the result by about as much. And K is not a constant. GB/T 1231-2024 §6.3.1 requires high-strength large hexagon head assemblies to be supplied with a batch mean torque coefficient between 0.110 and 0.150, with a coefficient of variation Vk no higher than 0.077. That is a supply requirement for one product family. It does not follow that every bolt in the store has K = 0.13, nor that a value from one chart transfers to another finish.
What the K Factor Actually Contains
Three torques act on the assembly at the same time, and K is their sum expressed as a fraction of F · d.
The helix term is the work of lifting the nut along the thread. Each revolution advances the nut by the pitch p, so the helix component of torque is F · p / (2π). Divide by F · d and the term becomes p / (2πd). For M12 coarse, GB/T 1231-2024 Table 1 gives p = 1.75 mm, so the term is 1.75 / (2π × 12) ≈ 0.023. For M20, p = 2.5 mm, giving 2.5 / (2π × 20) ≈ 0.020. At a K near 0.20 the geometry is roughly a tenth of the total; the rest is friction.
Thread friction is the second term: the flanks sliding under load, amplified by the 60° thread form. Bearing friction is the third: the nut face or bolt head rotating against a washer or the joint face at a larger radius. In most joints the bearing term is the largest, which is why washer condition matters as much as lubricant.
Here μt and μb are the thread and bearing friction coefficients, rt and rb the corresponding friction radii, and β is the thread half-angle, 30° for an ISO metric thread. Both friction coefficients are surface conditions: change the coating, lubricant, washer hardness or roughness and K changes without a dimension changing.
K by Finish and Lubrication
We do not publish a K table by finish. We have not measured K for every finish we supply, and a copied table would be a number without a batch behind it. What the standard fixes is narrower and more useful.
For GB/T 1231 assemblies the supplied batch carries a mean K between 0.110 and 0.150 and a Vk of 0.077 or less. Surface treatment is part of that: §6.8 requires a treatment that preserves both the torque coefficient and the anti-corrosion performance agreed with the buyer. The guarantee runs six months from the ex-factory date under §6.3.2, and §8.6 ties complaints to normal transport and storage.
Lubrication is the largest lever a site can pull. A dry zinc-plated assembly and the same assembly brushed with molybdenum disulphide are not the same joint at identical torque. Change the lubricant and the previous torque value is void until K is re-established.
So the practical request is not a torque table. Ask for the batch mean K, the Vk, the surface treatment and the test date. A supplier who can only send a chart has measured nothing for your order.
Why One Torque Is Not One Preload
Because the standard accepts a batch on a mean and a variation, the preload at a fixed torque inherits that variation. F = T / (K · d) is a reciprocal relation, so K moving up moves preload down by nearly the same percentage.
At the standard limit, mean K = 0.140 and Vk = 0.077 give a standard deviation of 0.0108 in K. One standard deviation either side is 0.129 and 0.151. At a fixed torque the preload then runs about 8.3% above the mean on the low-K side and 7.1% below it on the high-K side.
| K mean | Vk | K at -1σ | K at +1σ | Preload change at fixed torque |
|---|---|---|---|---|
| 0.140 | 0.077 | 0.129 | 0.151 | +8.3% / -7.1% |
Measurement adds its own layer. GB/T 32076.2-2015 requires axial force to be measured with an uncertainty of ±2% of the actual value and a repeatability of ±1%, torque to ±1%, angle to ±1° and elongation to ±0.01 mm. GB/T 1231-2024 §7.4.2 asks for a torque wrench of class 2 or better under JJG 707, with an error no larger than 2% of the measured torque. A correct joint can still be recorded outside its band because the bench was the problem.
Under §7.4.4 a preload outside the Table 14 range invalidates the coefficient. Under §7.4.5 the nut should turn at less than 5 r/min. Under §7.4.6 the fixture, instruments and assembly sit at the recorded ambient temperature for at least two hours, and under §7.4.7 a disputed test is run at 23 ± 5 °C. A K value quoted without those conditions cannot be reproduced.
Worked Example: M12, Property Class 8.8
This is an arithmetic example, not a recommendation for a specific joint.
Inputs: coarse M12, property class 8.8; nominal stress area As = 84.3 mm² from GB/T 1231-2024 Table 10; nominal tensile strength Rm = 800 MPa from GB/T 3098.1-2010 §7.1, Table 3; target preload Fp = 0.7 · Rm · As from the GB/T 32076.2-2015 definition; and an assumed K = 0.20 for this calculation.
Fp = 0.7 × 800 × 84.3 = 47,208 N ≈ 47.2 kN.
T = K · Fp · d = 0.20 × 47.2 × 12 = 113.3 N·m ≈ 113 N·m.
| Step | Input | Arithmetic | Result |
|---|---|---|---|
| Stress area | M12 coarse | Table 10 | 84.3 mm² |
| Target preload | Rm = 800 MPa | 0.7 × 800 × 84.3 | 47.2 kN |
| Torque at K = 0.20 | d = 12 mm | 0.20 × 47.2 × 12 | 113 N·m |
Cross-check the preload against a second clause. GB/T 1231-2024 Table 14 gives a preload window of 47 to 53 kN for an 8.8S M12 assembly in the coefficient test, and 47.2 kN sits just inside the bottom of that window. Agreement of that order is a good sign, not a validation of K = 0.20.
K changes the answer: at K = 0.15 the same preload needs 85.0 N·m; at K = 0.11 it needs 62.3 N·m. The target preload did not move; only the surface condition did.
Worked Example: M20, Property Class 10.9
Inputs: coarse M20, class 10.9 (the grade behind a 10.9S assembly); As = 245 mm² from Table 10; Rm nominal = 1000 MPa from GB/T 3098.1-2010 §7.1; so Fp = 0.7 × 1000 × 245 = 171,500 N ≈ 171.5 kN. At K = 0.20, T = 0.20 × 171.5 × 20 = 686 N·m.
| K | Torque for Fp = 171.5 kN | Note |
|---|---|---|
| 0.11 | 377 N·m | Bottom of the GB/T 1231 mean window |
| 0.15 | 515 N·m | Top of the same window |
| 0.20 | 686 N·m | Assumed dry value used above |
The GB/T 1231 window alone spans 377 to 515 N·m for the same bolt and the same preload, about 36% more torque at the top than at the bottom. A drawing that names one torque without naming K has hidden that spread inside a single number.
GB/T 3098.1-2010 also gives Rm minimum = 1040 MPa for class 10.9. Using the minimum gives Fp = 0.7 × 1040 × 245 ≈ 178.4 kN, near the top of the 161 to 179 kN window in GB/T 1231-2024 Table 14 for a 10.9S M20. State whether nominal or minimum Rm applies; here the choice moves the target by about 7 kN.
From Torque Back to Preload
Reverse the formula when the torque is fixed by a drawing or a customer, and the question is what it will actually deliver: F = T / (K · d). Take a 400 N·m callout on an M20 class 10.9 bolt.
| K | Preload at 400 N·m | Reading against Fp = 171.5 kN |
|---|---|---|
| 0.11 | 181.8 kN | Above the Table 14 window |
| 0.13 | 153.8 kN | Below the window |
| 0.15 | 133.3 kN | 17% below the bottom of the window |
| 0.20 | 100.0 kN | Badly under-tightened |
Four hundred newton-metres lands inside the 161 to 179 kN window only if K is between 0.112 and 0.124. If the batch mean is 0.15, the same torque delivers 133.3 kN, which is 17% short of the bottom of that window and about 22% short of Fp.
That is the honest answer to “how do I convert torque to preload”: you cannot, without K. With K the conversion is one division, and the acceptance decision is a comparison against Fp or against a project window.
When the comparison fails, the answer is not more torque. It is a different tightening method. Angle-controlled tightening, direct tension indicators and tensioners reduce or remove the dependence on K; they are chosen where the preload band matters. GB/T 32076.2-2015 §6 defines the evidence set for that choice: torque, angle, axial force and, where required, elongation recorded on the same assembly.
When a Chart Value Does Not Apply
A chart is a set of values computed at one K, for one thread form, finish and target stress. It stops applying when any of those change. Our checklist:
- fine pitch instead of coarse, because the helix term changes and most charts are coarse;
- a lubricant or anti-seize different from the one the chart assumed;
- stainless steel, or a coating system other than the chart’s;
- a reused bolt, where thread and bearing surfaces have already been run in;
- a different washer or flange face, which changes the bearing radius;
- stock older than the six-month guarantee in GB/T 1231-2024 §6.3.2, or storage unknown;
- a wrench that is not class 2 under JJG 707, or is out of calibration.
Two of these are easy to miss. Reuse is one: GB/T 1231-2024 §7.4.1 allows each assembly to be tested once, and GB/T 32076.2-2015 §6.3 says each part is used once. Storage is the other: the six-month guarantee is tied to normal transport and storage, so a K value from a 2023 test says nothing about a carton opened in 2026.
How We Check a Torque Value
When a customer sends a torque value for review, we run four checks before quoting anything.
- Recompute the preload from the torque with the batch K, never a catalogue K.
- Compare it with Fp = 0.7 · Rm · As for the stated grade.
- Compare it with any project or standard window, such as the GB/T 1231 Table 14 range.
- Decide whether the torque method is adequate, or whether the joint needs an angle or tensioner route.
Send the size, property class, finish or lubricant, target preload or target torque, and the standard the project cites to our technical review desk. We return the recomputation, the K assumption we used and the point at which the answer would change. How sources and corrections are handled is set out in our editorial policy; the values behind Rm are in the bolt grade strength chart and the property class guide.
Frequently Asked Questions
What is a normal K factor for a bolt?
There is no single normal value. For GB/T 1231-2024 high-strength large hexagon head assemblies the batch mean must be between 0.110 and 0.150 with Vk no higher than 0.077. For other bolts and finishes, K is whatever that batch measures; a generic 0.20 is an assumption.
Can I use one K value for every bolt in a project?
Only as a first estimate. Across the GB/T 1231 window alone, the same target preload needs about 36% more torque at K = 0.15 than at K = 0.11. On a mixed project the error lands on the joints with the least margin.
Why does a published torque chart disagree with my calculation?
Usually because the chart used a different K, a different target stress or a different thread form. A chart computed against proof strength and one computed at 0.7 · Rm · As are not the same target. Check the assumption behind the number first.
Does a calibrated torque wrench guarantee the preload?
No. A class 2 wrench under JJG 707 controls torque within about 2% in the coefficient test, but preload still depends on K. The wrench controls the input; K decides how much of it becomes clamp force.
What should I ask a supplier for?
The batch mean K and its Vk, the test conditions (23 ± 5 °C for a disputed test, nut speed below 5 r/min, a load cell within 2%), the surface treatment, the test date and the guarantee date. With those five items a torque value can be checked; without them it can only be repeated.
References
- GB/T 1231-2024 — High-strength bolts with large hexagon head assemblies for steel structures, §6.3 and §7.4
- GB/T 32076.2-2015 — High-strength structural bolting assemblies for preloading, Part 2: Suitability for preloading
- GB/T 3098.1-2010 — Mechanical properties of fasteners: bolts, screws and studs, §7.1 and Table 3
- [JJG 707 — Verification regulation of torque wrenches, cited by GB/T 1231-2024 §7.4.2]
Key Standards
Standards and clauses referenced by this article.
- High-strength bolts with large hexagon head assemblies for steel structures6.3.1, 6.3.2, 6.8, 7.4.1-7.4.7, 8.2, 8.6, Table 1, Table 10, Table 14
Sole source for the batch acceptance of the torque coefficient (mean K 0.110-0.150, Vk <= 0.077), the Ki = T/(F*d) definition and the coefficient-test validity conditions, plus the preload windows used as cross-checks. Values are quoted from the standard; the full text is not reproduced.
- High-strength structural bolting assemblies for preloading - Part 2: Suitability for preloadingClause 4 (Fp = 0.7 Rm As), 6.2, 6.3, 6.5, 6.6
Source for the nominal preload definition and for the measurement uncertainty of the torque-axial force test: axial force +/-2% with +/-1% repeatability, torque +/-1%, angle +/-1 degree, elongation +/-0.01 mm. Each part is used once per test.
- Mechanical properties of fasteners - Bolts, screws and studs5, 7.1, Table 3
Source for the property-class marking and for the tensile values used in the worked examples: 8.8 nominal Rm 800 MPa; 10.9 nominal Rm 1000 MPa and minimum Rm 1040 MPa.
- Verification regulation of torque wrenchescited by GB/T 1231-2024 §7.4.2
Accuracy class referenced for the torque wrench used in the coefficient test; class 2 or better, with an error no larger than 2% of the measured torque.
References
Sources used for fact checking and background context.
- SAMR openstd - official free full-text portal for GB standardsState Administration for Market Regulation / Standardization Administration of China
Deep Reading
More systematic selection, procurement, or inspection guides.
- Bolt Property Classes 4.8, 8.8 and 12.9
How the property-class marking maps to tensile and yield values
Related Solutions
Pages for specification checks and procurement discussion.
- Technical review of a torque value
Send size, class, finish or lubricant, target preload or torque, and the cited standard
- Bolt Torque Calculator
Runs T = K*D*F with the inputs given in this entry
This page is one entry in the fastener engineering reference. The library covers standards, dimensions, materials, and failure analysis; every figure is traced back to its source.
Continue reading in the library →