Why preload, not property class, sets fatigue life
A joint that keeps its preload puts only a fraction of the external load into the bolt. A joint that has lost it puts all of it in. For an M12 8.8 bolt under a 20 kN external load range, that difference is a bolt stress amplitude of 23.7 MPa against 118.6 MPa. Changing the same bolt from class 8.8 to 10.9 raises its tensile strength by 25% and moves neither number.
Where a bolt fatigue crack starts
Three locations account for most bolt fatigue failures: the thread root at the first engaged thread, the thread root a few threads further along the nut, and the fillet under the head. The shank is rarely one of them.
The thread root is a notch, and its section is the minor diameter, smaller than the shank, so local stress is higher than a nominal stress calculated on A_s. The first engaged thread also carries the largest share, because load transfer falls off along the engagement — highest stress and highest share coincide. The under-head fillet is the second notch; an undersized radius or a chamfered hole cutting into the bearing face moves the origin there.
The shank has no notch and a larger section, so it stays elastic while the root is already working at a concentration. Surface damage such as nicked threads, corrosion pits or chipped plating changes where cracking starts, not the rule: fatigue starts where local stress is highest, not where nominal stress is highest.
Rolled threads raise local fatigue resistance: material is displaced rather than cut, and grain flow follows the root contour. GB/T 32076.1-2015 §4 requires 10.9 bolts to be roll-threaded.
Why a higher property class does not add life
GB/T 3098.1-2010 Table 3 gives 8.8 as Rm 800 MPa and Rp0.2 640 MPa, and 10.9 as Rm 1000 MPa and Rp0.2 900 MPa — 25% more tensile strength and 41% more yield strength. The property class table sets out the full range.
None of it appears in the stress amplitude. For the same thread size A_s is the same, for the same external load F is the same, and for the same joint C is the same. Δσ = F·C/(2A_s) contains no strength term. What the higher class buys is headroom for preload: at M12, 0.7Rm·As rises from 47.2 kN to 59.0 kN. If the installation torque stays the same, the preload stays the same and so does the fatigue behaviour.
Higher-strength steel is also more notch-sensitive, and 10.9 carries a hydrogen-embrittlement risk that 8.8 does not (GB/T 32076.1-2015 §4). A 10.9 bolt with a damaged thread and uncontrolled plating can fail earlier, not later. That is not an argument against 10.9: each class fits a different job. It is an argument against changing class when the joint is not holding its preload.
How preload splits the external load
k_b is bolt stiffness, k_j the stiffness of the clamped parts, F_i preload, F_e external load. Bolt and parts act as springs in parallel: the external load must stretch the bolt and unload the parts by the same displacement, so the bolt takes the share set by its stiffness.
C is not a constant to look up: it depends on bolt size, grip length, bearing area and the modulus of the stack.
A worked estimate, assumptions stated: M12, 40 mm steel grip, E = 210 GPa, 18 mm bearing face. Bolt stiffness k_b = A_s·E/L_b = 84.3 × 210,000 / 49.2 = 360 kN/mm, with L_b = grip plus half nut and half head. The stack, modelled as a 30° frustum, gives k_j ≈ 3,700 kN/mm, so C = 0.09. The same geometry in aluminum (E = 70 GPa) gives C ≈ 0.23. A short grip or a soft gasket pushes C higher. C = 0.3 instead of 0.2 is a 50% higher stress amplitude at the same load.
One point is easy to miss. While the joint stays closed, ΔF_b = C·ΔF_e however high the preload is. Preload does not lower the amplitude continuously; it keeps the joint on the low-amplitude branch. At the separation load F_i/(1 − C) the parts stop contributing, C becomes 1, and the bolt takes everything — a step of five at C = 0.2.
Worked example: M12 8.8 at 20 kN
F is the peak-to-peak range of the external load, so the bolt’s alternating component is F·C/2. For M12 8.8, A_s = 84.3 mm².
| Stiffness ratio C | Bolt load range F·C (kN) | Stress amplitude Δσ (MPa) |
|---|---|---|
| 0.1 | 2.0 | 11.9 |
| 0.2 | 4.0 | 23.7 |
| 0.3 | 6.0 | 35.6 |
| 0.5 | 10.0 | 59.3 |
| 1.0 (separated) | 20.0 | 118.6 |
At C = 0.2, Δσ = 20,000 × 0.2 / (2 × 84.3) = 23.7 MPa. At C = 0.3, Δσ = 35.6 MPa. Separated, Δσ = 118.6 MPa. All three are calculated; the table has no property-class column because the answer does not depend on it.
When preload is lost, fatigue life goes with it
Four mechanisms remove preload, each with a different trace.
Separation. The external load exceeds F_i/(1 − C), the joint opens and the amplitude jumps by 1/C. At M12 8.8 with 47.2 kN preload and C = 0.2, separation starts at 59 kN.
Self-loosening. Transverse slip between the plates unscrews the nut. GB/T 10431-2008 uses a transverse vibration machine, recommends 12.5 Hz when the service frequency is unknown (§4.3), and sets amplitude so the bolt is not sheared. Annex B lists 40.9 kN and ±1.2 mm free amplitude for M12 at class 12.9. That 40.9 kN is 485 MPa on A_s, about 0.40Rm and below the 0.7Rm·As service preload of 70.8 kN, so the test runs lighter than service. The standard says results are comparative only (§1).
Embedment. Asperities at every interface flatten during the first load cycles. The loss grows with the number of interfaces and surface roughness, and most of it happens early; the trace is a preload that drops for a few days and then stabilises.
Gasket creep. A viscoelastic gasket keeps compressing with time and temperature. The trace is a preload that falls over weeks, not hours.
Preload targets and the 0.6-0.75 Rp0.2 band
GB/T 32076.2-2015 §4 defines the specified preload as F_p = 0.7R_m·A_s and uses it as the reference point for the rotation measurements. GB/T 32076.3-2015 §1 permits a preload of ≥0.7R_m·A_s for the HR assembly, and §6.4 requires the tightening test to reach F_bimax ≥ 0.9R_m·A_s. Against yield that is about 0.88 Rp0.2 for 8.8 and 0.78 Rp0.2 for 10.9.
| Thread | Pitch (mm) | A_s (mm²) | 8.8: 0.7R_m·A_s (kN) | 10.9: 0.7R_m·A_s (kN) |
|---|---|---|---|---|
| M8 | 1.25 | 36.6 | 20.5 | 25.6 |
| M10 | 1.5 | 58.0 | 32.5 | 40.6 |
| M12 | 1.75 | 84.3 | 47.2 | 59.0 |
| M16 | 2.0 | 157 | 87.9 | 109.9 |
| M20 | 2.5 | 245 | 137.2 | 171.5 |
| M24 | 3.0 | 353 | 197.7 | 247.1 |
All values are calculated as 0.7 × Rm × A_s, with Rm from GB/T 3098.1-2010 Table 3 and A_s from A_s = π/4 × ((d₂ + d₃)/2)², where d₂ = d − 0.6495P and d₃ = d − 1.2269P.
The 0.6-0.75 Rp0.2 band is a different kind of number: a design-practice range for joints tightened by torque without a tightening test, where friction scatter is absorbed by margin. Against the proof stress Sp in GB/T 3098.1-2010 Table 3, where Sp/Rp0.2 is 0.91 for 8.8 and 0.88 for 10.9, it corresponds to roughly 0.66-0.85 of proof load. No standard sets 0.6-0.75 Rp0.2 as a number; use 0.7R_m·A_s when the joint is qualified by a tightening test.
The torque route is M = k·F_p·d (GB/T 32076.10-2018 §8.3.2), and everything depends on k. GB/T 32076.3-2015 §6.5 accepts a mean k between 0.10 and 0.23 with a coefficient of variation Vk ≤ 0.10. Because F = M/(k·d), a 10% variation in k is a 10% variation in preload — about ±20% at two standard deviations and ±30% at three. The permitted mean range is 2.3:1, so a torque calculated for k = 0.165 delivers 72% of the target at k = 0.23 and 165% at k = 0.10. The K factor and torque calculation covers the friction terms behind k.
That is where the often-quoted ±25% comes from. It is an experience-level figure for a lubricated, tested batch, not a guarantee; dry or mixed lubrication does worse. Wrench calibration (±4%, §8.2.3) and the ±10% inspection window (§9.2.1) are smaller than the friction scatter and do not cover it.
What the two tests actually measure
MIL-STD-1312-5A, Method 5, is a stress durability test for externally threaded fasteners that may be subject to embrittlement (§1). The specimen is loaded to 75-80% of the minimum ultimate tensile strength and held at room temperature for a duration set by the procurement document (§5.1.1). Four loading methods are allowed, with external load as referee in a dispute. It measures whether a fastener under sustained high static stress cracks. It applies no cyclic load, so it says nothing about fatigue life.
GB/T 32076.2-2015 is a tightening test. The nut is rotated at 1-10 r/min while force, angle and torque are recorded (§5), and stops at the first of three conditions: rotation past θ_pi + Δθ2min, force falling back to F_p, or bolt fracture. The curves give the torque coefficient and its scatter, F_bimax, and the angle differences; GB/T 32076.3-2015 Table 7 sets minimum Δθ1 at 90°, 120° or 150° by grip length. It measures whether the assembly reaches and holds its specified preload without over-tightening or breaking — preload adaptability, and the scatter torque control must absorb.
1312-5A is a material and process screen at sustained load; 32076.2 is an assembly qualification at increasing load. Neither applies a cyclic load, so a joint that passes both can still fail in fatigue.
Choosing preload for steel, aluminum and composites
High preload with a high class fits steel-to-steel joints under cyclic tension or transverse load, where the clamped parts can carry the bearing pressure and the tightening method can control scatter. Set the target at 0.7R_m·A_s and qualify it with the tightening test.
Lower preload fits joints where the clamped material is the weak link. Aluminum has bearing-pressure and thread-stripping limits, and its lower modulus raises C, so the bolt already carries more. Composites are limited by through-thickness strength and delamination; plastics creep at room temperature, so preload decays without vibration. Thin-walled sections yield under the washer.
The trap is to lower preload and stop there: earlier separation multiplies Δσ by 1/C. When the preload must come down, recover the margin elsewhere: more bolts, a larger A_s, a longer grip, a hardened washer, or a threaded insert in the soft material. Then check the separated condition as well, not only the nominal C.
Before the next torque specification
A joint review puts these numbers in one calculation: a value chosen for preload changes both the stiffness ratio and the separation load.
References
- GB/T 32076.2-2015 — Preload adaptability (§4, §5)
- GB/T 32076.3-2015 — HR system assemblies (§1, §6.4, §6.5, Table 7)
- GB/T 32076.10-2018 — Assembly specifications (§8.2.3, §8.3.2, §9.2.1)
- GB/T 3098.1-2010 — Mechanical properties of bolts, screws and studs (Table 3)
- GB/T 10431-2008 — Transverse vibration test method for fasteners (§1, §4.3, Annex B)
- MIL-STD-1312-5A — Fastener test methods, Method 5: stress durability (§1, §5.1.1)
Key Standards
Standards and clauses referenced by this article.
- Mechanical properties of bolts, screws and studs (Table 3: Rm, Rp0.2, Sp)
- High-strength structural bolting assemblies for preloading, Part 1: general requirements (§4)
- High-strength structural bolting assemblies for preloading, Part 2: suitability for preloading (§4, §5)
- High-strength structural bolting assemblies for preloading, Part 3: HR system (§1, §6.4, §6.5, Table 7)
- High-strength structural bolting assemblies for preloading, Part 10: assembly specifications (§8.2.3, §8.3.2, §9.2.1)
- Transverse vibration testing method for fasteners (§1, §4.3, Annex B)
- Fastener test methods, Method 5: stress durability (§1, §5.1.1)
References
Sources used for fact checking and background context.
- GB/T 32076.2-2015 — Suitability for preloading (§4, §5)SAMR
- GB/T 32076.3-2015 — HR system assemblies (§1, §6.4, §6.5, Table 7)SAMR
- GB/T 32076.10-2018 — Assembly specifications (§8.2.3, §8.3.2, §9.2.1)SAMR
- GB/T 3098.1-2010 — Mechanical properties of bolts, screws and studs (Table 3)SAMR
- GB/T 10431-2008 — Transverse vibration testing method for fastenersSAMR
- MIL-STD-1312-5A — Fastener test methods, Method 5: stress durabilityU.S. Department of Defense
Deep Reading
More systematic selection, procurement, or inspection guides.
- Fastener Receiving Inspection Checklist
Incoming checks for grade, thread and coating
- EN 10204 3.1 vs 3.2: Which Certificate to Order
Documentation of the measured properties
This page is one entry in the fastener engineering reference. The library covers standards, dimensions, materials, and failure analysis; every figure is traced back to its source.
Continue reading in the library →