Thread Stripping: Why Nut Height Decides Which Part Fails
24 min·Yaxiio Engineering Alliance

Thread Stripping: Why Nut Height Decides Which Part Fails

Nut height and thread shear area decide whether a joint strips or the bolt breaks. M8-M20 limits, grade pairing and a worked M12 8.8 example.

Why the nut strips before the bolt breaks

A joint that fails with the screw intact and the nut thread wiped has answered one question: the engaged thread, not the bolt shank, was the weaker path. Three conditions produce that symptom: a nut of lower grade than the bolt, an engaged length too short to develop the thread shear area, or a parent material softer than the bolt. The comparison that separates them is the bolt’s tensile capacity against the shear capacity of the engaged threads. In a matched joint the bolt should break first. When the nut strips, one assumption behind that match has failed.

Two failure paths, one area comparison

Under axial tension the bolt can fail across its threaded section:

Formula
F_t=A_s×R_m

A_s is the tensile stress area, not the shank area. It is based on a diameter about midway between the pitch and minor diameters, because a threaded part fails at a load close to that of an unthreaded part of that intermediate diameter (FED-STD-H28/2B §70.1).

The second path is shear through the engaged threads:

Formula
F_s=τ×A_shear

Whichever is lower decides the failure mode. For M12 8.8, A_s is 84.3 mm² and R_m is 800 MPa (GB/T 3098.1-2010 Table 3), giving F_t = 67.4 kN. The shank area is π/4 × 12² = 113.1 mm², about one third larger. Using the shank area overstates tensile capacity by the same proportion.

How to calculate thread shear area

Two simplified expressions cover the usual cases:

Formula
A_shear,ext≈0.5×π×d_3×L_e
A_shear,int≈0.5×π×D×L_e
d_3=d − 1.2269P

d is nominal diameter, P pitch, d_3 external thread minor diameter from the basic 60° profile, D internal thread major diameter, and L_e full-form engagement. The factor 0.5 reflects that the thread ridge occupies roughly half of each pitch at the shear diameter. This is a simplified geometric estimate; FED-STD-H28/2B §70.4 notes that empirical simplified formulas differ from exact minimum-material geometry, and §70.5 notes that thread bending reduces the effective area further.

L_e is not the nut height m. A completely formed thread is defined over an axial distance of one pitch, and the lead-in thread at the end of a product should not exceed 2P (FED-STD-H28/21B §4.6.1 and §4.6.2.1). Chamfers and incomplete threads therefore reduce the full-form engagement below the overall height. Tolerance also matters: the standard metric fit is 6H internal and 6g external (FED-STD-H28/21B §5.1.1), and a plated or oversized internal thread can lower the stripping load at unchanged nominal dimensions.

Why thread turns do not add up linearly

Multiplying one turn’s shear area by the number of turns overstates capacity. The bolt elongates and the nut compresses, so the first engaged thread at the bearing face sees the largest relative displacement and carries the largest share. The share falls along the engagement. Thread bending during failure further reduces the effective area (FED-STD-H28/2B §70.5).

Engagement therefore has diminishing returns. In practice, beyond roughly one diameter, extra turns add little static stripping resistance, and the first threads remain the fatigue crack origins. The design question is the full-form engaged length, not the number of visible turns.

What GB/T 6170 nut height actually buys

GB/T 6170-2015 sets the dimensions of the type 1 hexagon nut. For M8 to M20:

Size Pitch P (mm) m max (mm) m min (mm) m min / d A_s (mm²) F_t at 800 MPa (kN) A_shear at m min (mm²) F_s at 461.6 MPa (kN)
M8 1.25 6.80 6.44 0.805 36.6 29.3 65.4 30.2
M10 1.5 8.40 8.04 0.804 58.0 46.4 103.0 47.6
M12 1.75 10.80 10.37 0.864 84.3 67.4 160.5 74.1
M16 2.0 14.80 14.10 0.881 156.7 125.3 300.0 138.5
M20 2.5 18.00 16.90 0.845 244.8 195.8 449.5 207.5

m values are from Table 1 (§3.1–3.2); A_s is calculated from the stress-area formula; F_t uses 800 MPa for grade 8.8; F_s uses the von Mises shear estimate τ = 0.577 × 800 = 461.6 MPa and m min. The last column is external thread shear, the lower of the two thread shear paths in a matched-strength nut.

m min/d runs from 0.805 to 0.881 and m max/d from 0.84 to 0.93. The rule that nut height is about 0.8d is a lower bound, not an arbitrary shop number. GB/T 32076.4-2015 §1 states the same intent for its high-strength system: nut height approximately 0.8D. Standard height keeps thread shear capacity slightly above bolt tensile capacity for a matched grade pair. In every row F_s is 1.03 to 1.10 times F_t, so the bolt should break first.

Use m min, not m max, in a capacity estimate. The maximum is a tolerance boundary, not a guaranteed value.

Grade pairing: 8.8 bolt, 8 nut

GB/T 3098.2-2015 §4 defines the nut grade number as the highest bolt class it can pair with: grade 8 with 8.8, grade 10 with 10.9, grade 12 with 12.9. A higher nut grade may replace a lower one; the reverse is not allowed (§5).

The pairing states which part may become the weak link. A grade 5 nut is qualified only to 5.8. On an 8.8 bolt, its thread becomes the shear path that fails first even though the bolt is stronger. The same applies to unmarked nuts and to thin nuts. GB/T 3098.2-2015 §5 states that 0 type thin nuts are not designed for stripping resistance; they are locking nuts used with a standard or high nut.

The nut grade is written “8”, not “8.8”. Internal threads with a positive basic deviation, such as 6AZ or 6AX for hot-dip galvanized nuts, may also have lower stripping strength than 6H.

Soft parent metals and wire thread inserts

In thin sheet, aluminium, plastics and cast iron, the parent thread is usually weaker than the bolt. Lengthening engagement often does not restore the joint:

  • the failure is in the parent thread, and a longer bolt does not increase its shear area;
  • plate thickness, not bolt length, caps L_e;
  • aluminium and plastics creep, so preload is lost under a load a static calculation calls safe;
  • cast iron chips at the flanks and concentrates stress instead of shearing cleanly.

A wire thread insert changes the load path. GB/T 24425.1-2009 states that general type inserts raise the strength of tapped holes in low-strength parent materials such as aluminium, magnesium, copper alloys, cast iron and non-metals, improve screw fatigue strength, and repair damaged threads (§1). The installed insert forms a 6H internal thread. Its external thread cuts into a larger hole, spreading load over more parent material; for M8 the free-state outside diameter is 9.85 mm to 10.35 mm (Table 1, §3.1) against a nominal 8 mm.

An insert does not replace parent thickness. It raises local thread strength but does not make a 2 mm plate carry an 8.8 bolt. The parent still has to carry bearing and tear-out loads around the insert.

Worked example: M12 8.8 with a standard nut

Take M12 coarse, P = 1.75 mm, grade 8.8 bolt, standard GB/T 6170 grade 8 nut.

  1. Stress area. d_2 = 12 − 0.6495 × 1.75 = 10.863 mm; d_3 = 12 − 1.2269 × 1.75 = 9.853 mm. Mean diameter 10.358 mm, so A_s = π/4 × 10.358² = 84.3 mm².
  2. Tensile capacity. F_t = 84.3 × 800 = 67,440 N = 67.4 kN. The 800 MPa figure is a specification minimum; a tensile test to MIL-STD-1312-8A §1.1 measures the fastener itself, not the joint.
  3. Shear area. With m min = 10.37 mm, A_shear = 0.5 × π × 9.853 × 10.37 = 160.5 mm².
  4. Shear capacity. Using the von Mises shear estimate, τ = 0.577 × 800 = 461.6 MPa, so F_s = 461.6 × 160.5 = 74,100 N = 74.1 kN.
  5. Comparison. F_s / F_t = 1.10, so the bolt breaks before the thread strips.

Critical engagement is found by setting F_s equal to F_t:

Formula
L_e,crit=A_s/(0.577×0.5×π×d_3)=2A_s/(0.577×π×d_3)

For M12, L_e,crit = 168.6 / (0.577 × 3.1416 × 9.853) = 9.44 mm, or 0.79d. The FED-STD-H28/2B §70.7.1 convention requires a shear area of 2A_s to develop the full tensile strength; with τ = 0.5R_m, that gives 4A_s / (π d_3) = 10.89 mm, or 0.91d. The two assumptions bracket the result at about 0.8d to 0.9d.

At 0.5d, or 6 mm, A_shear = 92.9 mm² and F_s = 42.9 kN, below F_t = 67.4 kN. The thread strips first. This is why a full-height nut, not a thin nut, belongs on a structural joint.

The result is an estimate, not a test value. It assumes matched strength, a von Mises shear strength of 0.577R_m, a simplified half-pitch area, uniform load, no thread bending, and room temperature. A lower nut grade, a soft parent thread, a short full-form engagement or a galvanized tolerance moves failure back to the thread. For preload after sizing, see the M12 bolt torque chart.

Reading the failure at the bench

Field guidance, not a laboratory diagnosis:

  • Overload tension. Necking, cup-and-cone or a 45° shear lip, reduced diameter, fracture at the thread run-out or reduced shank, threads away from the fracture still formed. Load exceeded A_s × R_m.
  • Thread stripping. Threads flattened or smeared helically, no necking, nut turns off or falls away, damage confined to the engaged length. Load exceeded the shear capacity of the weaker thread.
  • Fatigue. Flat smooth face, beach marks or ratchet marks, crack at a thread root or head-to-shank fillet, small final overload zone, no gross deformation. Cyclic load, often after preload loss.

Hydrogen embrittlement is a fourth mode in high-strength plated fasteners: brittle intergranular fracture, little deformation, sometimes hours after tightening. It is not stripping, and it needs laboratory analysis.

Three checks settle most cases: nut grade matches bolt class; full-form engagement is at least about 0.8d; the parent thread has enough shear area. If all three pass and the nut still strips, material or tolerance is the remaining variable.

Run the checklist below before re-tightening a joint that has already stripped once.

Takeaway Checklist
Copy this checklist into your tender documents
Selected conditions
Tap to check, this is your procurement checklist
References

If the joint has failed, record bolt class, nut grade, nut height, full-form engaged length and parent material before replacing anything. Those five values let an engineer review the match and decide between a higher nut grade, a longer engagement, a wire thread insert or a different parent material. The bolt property class guide covers the grade side; the torque chart covers preload once the joint is correctly sized.

Key Standards

Standards and clauses referenced by this article.

  1. 1 type hexagon nuts — dimensions (Table 1, §3.1–3.2)
  2. Mechanical properties of nuts (§4–§5)
  3. Mechanical properties of bolts, screws and studs (Table 3)
  4. General type wire thread inserts (§1, §3.1)
  5. High-strength structural bolting assemblies, HV system (§1)
  6. Screw thread standards for federal services (§70.1–§70.7.4)
  7. Metric screw thread standards (§5.1.1)
  8. Fastener test methods, Method 8: tensile strength (§1.1, §5.2, §5.6)

References

Sources used for fact checking and background context.

  1. GB/T 6170-2015 — 1 type hexagon nuts, dimensions (Table 1)SAMR
  2. GB/T 3098.2-2015 — Mechanical properties of nuts (§4–§5)SAMR
  3. GB/T 24425.1-2009 — General type wire thread inserts (§1, §3.1)SAMR
  4. FED-STD-H28/2B — Screw thread standards for federal services, §70U.S. General Services Administration
  5. MIL-STD-1312-8A — Fastener test methods, Method 8: tensile strengthU.S. Department of Defense

Deep Reading

More systematic selection, procurement, or inspection guides.

This page is one entry in the fastener engineering reference. The library covers standards, dimensions, materials, and failure analysis; every figure is traced back to its source.

Continue reading in the library →