Engineering Tools · Hex Bolt Dimension Reference
M30 Bolt Size Chart: Head Size & Hex Head Dimensions s, e and k
M30 in both standards and both product grades
One row per thread form and product grade. The head columns repeat because ISO 4017 / GB/T 5783-2025 and ISO 4014 / GB/T 5782-2025 share the same head; b is tabulated in ISO 4014 / GB/T 5782-2025 only, and a dash means the standard does not tabulate that value for the combination.
| Thread form | Product grade | Coarse pitch P (mm) | Width across flats s (mm, nominal = max) | s min (mm) | Width across corners e min (mm) | Head height k (mm, nominal) | k max (mm) | b at l ≤ 125 mm | b at 125 < l ≤ 200 mm | b at l > 200 mm |
|---|---|---|---|---|---|---|---|---|---|---|
| Fully threaded (ISO 4017 / GB/T 5783-2025) | A | — | — | — | — | — | — | — | — | — |
| Fully threaded (ISO 4017 / GB/T 5783-2025) | B | 3.5 | 46 | 45 | 50.85 | 18.7 | 19.12 | — | — | — |
| Partially threaded (ISO 4014 / GB/T 5782-2025) | A | — | — | — | — | — | — | — | — | — |
| Partially threaded (ISO 4014 / GB/T 5782-2025) | B | 3.5 | 46 | 45 | 50.85 | 18.7 | 19.12 | 66 | 72 | 85 |
Head figures are the standard's nominal (= max) or minimum values, so a delivered bolt measures at those bounds or inside them. s is what you buy a socket by, e is the diagonal a 12-point socket has to clear, and k is the head height. Small and large sizes follow the same three columns, up to s = 95 mm at M64.
Full PDF
Download the full PDF (M1.6–M64, all sizes)
Printable chart covering every size in this family — enter your email to get it.
Other sizes
Metric bolt size chart M1.6–M64 (mm)
The two standards share the same hex head: ISO 4017 / GB/T 5783-2025 (fully threaded) and ISO 4014 / GB/T 5782-2025 (partially threaded) give identical s, e, k and r for a size, so only the thread length differs. Switch the thread form to add the b columns, and the product grade to see the A-grade or B-grade tolerance band.
Thread form
Product grade
Partially threaded (ISO 4014 / GB/T 5782-2025) · ISO 4014 / GB/T 5782-2025 · Grade B
Grade A and grade B are dimensional tolerance grades, not quality grades: the nominal s and k are the same, only the tolerance band differs (s min, e min, k max). Grade A applies to d ≤ M24 with l ≤ 10d or l ≤ 150 mm; grade B covers every size in this table.
| Size | Coarse pitch P (mm) | Width across flats s (mm, nominal = max) | s min (mm) | Width across corners e min (mm) | Head height k (mm, nominal) | Fillet radius r min (mm) | b at l ≤ 125 mm | b at 125 < l ≤ 200 mm | b at l > 200 mm |
|---|---|---|---|---|---|---|---|---|---|
| M1.6 | 0.35 | 3.2 | 2.9 | 3.28 | 1.1 | 0.1 | 9 | 15 | 28 |
| M2 | 0.4 | 4 | 3.7 | 4.18 | 1.4 | 0.1 | 10 | 16 | 29 |
| M2.5 | 0.45 | 5 | 4.7 | 5.31 | 1.7 | 0.1 | 11 | 17 | 30 |
| M3 | 0.5 | 5.5 | 5.2 | 5.88 | 2 | 0.1 | 12 | 18 | 31 |
| M3.5 | 0.6 | 6 | 5.7 | 6.44 | 2.4 | 0.1 | 13 | 19 | 32 |
| M4 | 0.7 | 7 | 6.64 | 7.5 | 2.8 | 0.2 | 14 | 20 | 33 |
| M5 | 0.8 | 8 | 7.64 | 8.63 | 3.5 | 0.2 | 16 | 22 | 35 |
| M6 | 1 | 10 | 9.64 | 10.89 | 4 | 0.25 | 18 | 24 | 37 |
| M7 | 1 | 11 | 10.57 | 11.94 | 4.8 | 0.25 | 20 | 26 | 39 |
| M8 | 1.25 | 13 | 12.57 | 14.2 | 5.3 | 0.4 | 22 | 28 | 41 |
| M10 | 1.5 | 16 | 15.57 | 17.59 | 6.4 | 0.4 | 26 | 32 | 45 |
| M12 | 1.75 | 18 | 17.57 | 19.85 | 7.5 | 0.6 | 30 | 36 | 49 |
| M14 | 2 | 21 | 20.16 | 22.78 | 8.8 | 0.6 | 34 | 40 | 53 |
| M16 | 2 | 24 | 23.16 | 26.17 | 10 | 0.6 | — | 44 | — |
| M18 | 2.5 | 27 | 26.16 | 29.56 | 11.5 | 0.6 | — | 48 | — |
| M20 | 2.5 | 30 | 29.16 | 32.95 | 12.5 | 0.8 | — | 52 | — |
| M22 | 2.5 | 34 | 33 | 37.29 | 14 | 0.8 | — | 56 | 69 |
| M24 | 3 | 36 | 35 | 39.55 | 15 | 0.8 | — | 60 | 73 |
| M27 | 3 | 41 | 40 | 45.2 | 17 | 1 | 60 | 66 | 79 |
| M30 | 3.5 | 46 | 45 | 50.85 | 18.7 | 1 | 66 | 72 | 85 |
| M33 | 3.5 | 50 | 49 | 55.37 | 21 | 1 | 72 | 78 | 91 |
| M36 | 4 | 55 | 53.8 | 60.79 | 22.5 | 1 | — | 84 | 97 |
| M39 | 4 | 60 | 58.8 | 66.44 | 25 | 1 | — | 90 | 103 |
| M42 | 4.5 | 65 | 63.1 | 71.3 | 26 | 1.2 | — | 96 | 109 |
| M45 | 4.5 | 70 | 68.1 | 76.95 | 28 | 1.2 | — | 102 | 115 |
| M48 | 5 | 75 | 73.1 | 82.6 | 30 | 1.6 | — | 108 | 121 |
| M52 | 5 | 80 | 78.1 | 88.25 | 33 | 1.6 | — | 116 | 129 |
| M56 | 5.5 | 85 | 82.8 | 93.56 | 35 | 2 | — | — | 137 |
| M60 | 5.5 | 90 | 87.8 | 99.21 | 38 | 2 | — | — | 145 |
| M64 | 6 | 95 | 92.8 | 104.86 | 40 | 2 | — | — | 153 |
Partially threaded: the standard gives b as a reference value in three nominal-length bands (b ≈ 2d + 6 at l ≤ 125 mm, ≈ 2d + 12 at 125 < l ≤ 200 mm, ≈ 2d + 25 at l > 200 mm). A dash means that band is not applicable for the size.
References
- GB/T 5783-2025 Hexagon head bolts, fully threaded - width across flats s, s min, width across corners e min, head height k and fillet radius r min, product grades A and B; thread length rule b = l − a
- GB/T 5782-2025 Hexagon head bolts, partially threaded - the same head dimensions, plus the thread length b in three nominal-length bands (l ≤ 125 mm, 125 < l ≤ 200 mm, l > 200 mm)
- GB/T 5785-2025 Hexagon head bolts with fine pitch thread - fine pitch options per nominal diameter and the same hex head (s, e, k unchanged)
- Table values are the nominal (= max) or minimum figures of the standard editions above, checked row by row against the official text. No table values are reproduced from third-party dimension tables, and every row is labelled with the standard it comes from.
Thread length b on partially threaded bolts (ISO 4014 / GB/T 5782)
A partially threaded hex bolt carries thread over part of the shank, so the threaded length b depends on the nominal length l as well as on the diameter. ISO 4014 / GB/T 5782 tabulates b as a reference value in three nominal-length bands; the same M-size therefore has up to three different thread lengths.
b ≈ 2d + 6 at l ≤ 125 mm, b ≈ 2d + 12 at 125 < l ≤ 200 mm, b ≈ 2d + 25 at l > 200 mm; the tabulated figure is that value rounded to a whole millimetre. Grade A tables carry the shorter bands only; grade B carries the band that applies to each size.
Thread length b by length band, grade B (mm)
| Size | b at l ≤ 125 mm | b at 125 < l ≤ 200 mm | b at l > 200 mm |
|---|---|---|---|
| M30 | 66 | 72 | 85 |
A dash means the standard does not tabulate that band for the size — the size's standard length range does not reach that length band (large sizes start above 125 mm) or the table carries only the bands in use.
Quote the diameter and the length together: b follows l, so only "M12×100" pins the thread length down.
Fine pitch hex bolts (ISO 8765 / GB/T 5785): fine thread against coarse thread
ISO 8765 / GB/T 5785-2025 tabulates the same hex head with a fine pitch thread on nominal diameters from 8 mm to 64 mm. The head does not change — s, e, k and r stay exactly as in the coarse table above — so a fine thread must be called out with its pitch: M12×1.5 is not M12, whose coarse pitch is 1.75 mm.
One diameter, one head: every fine pitch of the same d shares the same s, e, k and r, so the socket size does not change with the pitch.
| Nominal diameter d (mm) | Fine pitch P (mm) | Coarse pitch P (mm) |
|---|---|---|
| M30 | 2 | 3.5 |
A pitch in brackets is the non-preferred fine pitch of that diameter in ISO 8765 / GB/T 5785-2025; diameters not listed have no fine thread series in that standard.
Which number do you need: s, e or k?
"Bolt size" means three different numbers depending on the job, and order codes use a fourth. Buying a tool uses s, checking a head that will not go into a socket uses e, and a counterbore or a flush-head check uses k.
s — width across flats (nominal = max)
M30 is s = 46 mm. This is the socket, spanner or ring size, and the number stamped on the tool. It is the same in grade A and grade B and the same in ISO 4017 / GB/T 5783-2025 and ISO 4014 / GB/T 5782-2025, because the two standards share the hex head.
e — width across corners (min)
M30 is e min = — mm in grade A and 50.85 mm in grade B. This is the diagonal between two opposite corners of the head, the dimension that decides whether a 12-point socket or a ring spanner passes over the head. Most published bolt size charts leave this column out; it is also what you can still measure with a caliper once the flats have been rounded off.
k — head height (nominal, with a max)
M30 is k = 18.7 mm nominal and 19.12 mm max in grade B. It sets how deep a counterbore or recess has to be and how far the head stands above the part. When the head must not protrude, k is the number to check, not s.
d — nominal thread diameter
The number in the callout: M30 is a 30 mm thread, not a 30 mm head. The head is always wider, 46 mm across the flats here, which is where ordering by "size" alone goes wrong.
r — fillet radius under the head (min)
r min = 1 mm at M30. The washer face has to clear this radius, so it matters when the bolt sits in a corner, against a shoulder or in a slotted hole rather than on a flat face.
Metric to inch bolt sizes (approximate, not interchangeable)
Cross-reference by nominal diameter only. The inch column is a straight millimetre-to-inch conversion of d; the last column is the inch hex bolt whose nominal diameter is closest to it.
| Metric size | Nominal d (mm) | Nominal d (in) | Closest inch hex bolt |
|---|---|---|---|
| M30 | 30 | 1.181 | 1-1/8 in (28.575 mm) |
matched by nominal diameter only
Do not substitute. Both series use a 60° thread form, but the diameters and thread counts differ, so a near-diameter inch bolt starts and then jams and damages the thread. Use these rows to read which callout a drawing means, not to interchange parts.
M30 beside the next sizes
The sizes either side of M30. Measure the thread diameter d with a caliper and compare the head against the rows below before ordering; the nominal diameter steps by 0.5 mm or 1 mm in this range.
Grade B
| Size | Coarse pitch P (mm) | Width across flats s (mm, nominal = max) | Width across corners e min (mm) | Head height k (mm, nominal) |
|---|---|---|---|---|
| M27d = 27 | 3 | 41 | 45.2 | 17 |
| M30d = 30 | 3.5 | 46 | 50.85 | 18.7 |
| M33d = 33 | 3.5 | 50 | 55.37 | 21 |
Cite this chart
YAXIIO. {size} Bolt Size Chart: Head Size & Hex Head Dimensions s, e and k. https://www.yaxiio.com/en/tools/bolt-size-chart/m30 (accessed 2026-11-17).
Free to cite and embed — attribution required: “YAXIIO” + a link to this page.
FAQ
Is the M number on an M30 bolt the head size?
No. M30 is the nominal thread diameter d = 30 mm, while the head is wider: 46 mm across the flats and 50.85 mm across the corners in grade B. Order by the M number and the length, and check s and k against the drawing or the counterbore.
Does an M30 fine pitch bolt take the same socket?
Yes, the head is the same: ISO 8765 / GB/T 5785-2025 uses the same hex head for the fine thread series, so s = 46 mm and k = 18.7 mm hold for a fine M30 too. Only the pitch changes — 3.5 mm coarse against the fine options 2. Write the pitch into the callout for a fine bolt: a plain M30 will be read as coarse pitch.
Can an M30 bolt be replaced by an inch bolt?
No, not as a substitute. The M30 thread is d = 30 mm with a 3.5 mm pitch, and the nearest inch bolt only matches the diameter to within a few tenths of a millimetre while carrying a different thread count, so it will not run true in the same nut or tapped hole and will damage it. Both are 60° threads, which is why they look close on a drawing; use the metric to inch table to read a callout, and order the thread the joint is made for.
Next: work out your order, or pick the size by standard
Same-size pages of related tools only cover these ranges: bolt weight chart M6–M36, wrench and socket chart M6–M36, carriage bolt chart M6–M20. Links outside those ranges are hidden rather than pointed at a default size.
Related References
Bolt Weight Chart
Unit weight and order total for hex bolts M6-M36 once the size and length are known, with the same catalogue coefficients the product pages use.
Bolt Torque Chart
Tightening torque and preload per size and property class, on the same size axis as this table.
Bolt Weight Calculator
Total weight and packing quantity for an order of hex bolts, with the size carried over from this page.
Wrench and Socket Size Chart
The opening across flats for each metric size and the tools that fit, which is the s column read the other way round.
Hex Head Bolts, Partially Threaded (GB/T 5782-2025)
The partially threaded range we quote to GB/T 5782, with the technical package for that standard.
Hex Head Bolts, Fully Threaded (ISO 4017 / DIN 933 / GB/T 5783-2025)
Sizes, property classes and finishes we quote to ISO 4017 / DIN 933 / GB/T 5783 — the same form in all three.
Hex Head Bolt Category
Standard numbers and head forms in the catalogue; sizes and lengths made to drawing.
Tap Drill Chart for M30 Threads
The hole to bore before tapping the same M30 thread, with the rule value d − P and the nearest drill in the metric set.
Disclaimer: this table is a selection and quotation reference built from the standard editions named on this page, not a design basis or an acceptance standard.