ENGINEERING TOOL
M6 Bolt Torque Chart: Specs, Values & Settings
Class 8.8 · Target preload (kN) 9
| Dry / Black | 11 N·m 10–12 |
| Electro Zinc | 9 N·m 8–11 |
| Hot-Dip Galv. | 12 N·m 10–14 |
| Oiled | 7 N·m 6–8 |
M6 bolt torque spec: class 8.8 dry is 11 N·m (8 ft·lb). Values cover six property classes across five friction states — dry, zinc, HDG, oiled and anti-seize. K-factor method, basis fully disclosed.
Full PDF
Download the full PDF (M6–M36, all sizes)
Printable chart covering every size in this family — enter your email to get it.
Other sizes
Torque by Property Class and Friction State
Quick answer: class 8.8 · dry / black ≈ 11 N·m (10–12); other classes and friction states below.
| Class | Rp0.2 (MPa) | Target preload (kN) | Dry / Black K 0.18–0.22 · N·m | Electro Zinc K 0.15–0.2 · N·m | Hot-Dip Galv. K 0.18–0.25 · N·m | Oiled K 0.12–0.15 · N·m | Wax / PTFE / Anti-seize K 0.08–0.12 · N·m |
|---|---|---|---|---|---|---|---|
| 4.8 | 340 | 4.8 | 6 5–6 | 5 4–6 | 6 5–7 | 4 3–4 | 3 2–3 |
| 8.8 | 640 | 9 | 11 10–12 | 9 8–11 | 12 10–14 | 7 6–8 | 5 4–6 |
| 10.9 | 940 | 13.2 | 16 14–17 | 13 12–16 | 17 14–20 | 10 10–12 | 8 6–10 |
| 12.9 | 1100 | 15.5 | 19 17–20 | 16 14–19 | 20 17–23 | 12 11–14 | 9 7–11 |
| A2-70 | 450 | 6.3 | 8 7–8 | 6 6–8 | 8 7–9 | 5 5–6 | 4 3–5 |
| A4-80 | 600 | 8.4 | 10 9–11 | 9 8–10 | 11 9–13 | 7 6–8 | 5 4–6 |
Cell shows the typical value; the small line below is the range (min–max).
References
- ISO 898-1:2013 — Mechanical properties of fasteners made of carbon and alloy steel
- ISO 3506-1:2020 — Mechanical properties of corrosion-resistant stainless steel fasteners (A2/A4)
- GB/T 3098.1-2010 — Mechanical properties of bolts, screws and studs (CN national standard, official full text)
- GB/T 3098.6-2014 — Mechanical properties of stainless steel bolts, screws and studs (CN, official full text)
- ISO 16047:2005 — Fasteners: torque/clamp force testing (K-factor measurement method)
- Machinery's Handbook (30th ed.) — empirical K-factor ranges
- Machine Design — anti-seize compound friction test (K≈0.10)
Fine-Thread Torque Matrix
Fine-thread series (M6 × 1 mm) target preload and tightening torque ranges, same basis as the coarse chart; the fine-thread stress area As follows ISO 898-1:2013 Table 6 (this page takes M6 As = 20.1 mm²).
M6 is not covered by the fine-thread stress area table of ISO 898-1:2013 (Table 6 starts at M8×1); the fine-thread values shown on this page equal the coarse chart.
| Class | Rp0.2 (MPa) | Target preload (kN) | Dry / Black K 0.18–0.22 · N·m | Electro Zinc K 0.15–0.2 · N·m | Hot-Dip Galv. K 0.18–0.25 · N·m | Oiled K 0.12–0.15 · N·m | Wax / PTFE / Anti-seize K 0.08–0.12 · N·m |
|---|---|---|---|---|---|---|---|
| 4.8 | 340 | 4.8 | 6 5–6 | 5 4–6 | 6 5–7 | 4 3–4 | 3 2–3 |
| 8.8 | 640 | 9 | 11 10–12 | 9 8–11 | 12 10–14 | 7 6–8 | 5 4–6 |
| 10.9 | 940 | 13.2 | 16 14–17 | 13 12–16 | 17 14–20 | 10 10–12 | 8 6–10 |
| 12.9 | 1100 | 15.5 | 19 17–20 | 16 14–19 | 20 17–23 | 12 11–14 | 9 7–11 |
| A2-70 | 450 | 6.3 | 8 7–8 | 6 6–8 | 8 7–9 | 5 5–6 | 4 3–5 |
| A4-80 | 600 | 8.4 | 10 9–11 | 9 8–10 | 11 9–13 | 7 6–8 | 5 4–6 |
Cell shows the typical value; the small line below is the range (min–max).
Basis of Calculation & Sources
Calculation basis
- Torque follows the K-factor (nut factor) method T = K·D·F: D is the nominal diameter and F the target preload = 70% of Rp0.2 × thread stress area (M6 As = 20.1 mm²).
- Yield strengths are published values from ISO 898-1 (carbon/alloy steel) and ISO 3506-1 (stainless A2/A4).
- K follows published empirical ranges per friction condition (Machinery's Handbook; the wax/PTFE/anti-seize band K≈0.10 follows Machine Design test data).
- The grease/MoS₂ band (K≈0.11) nearly overlaps anti-seize and is available in the calculator instead of a separate column.
Stainless note: A2/A4 austenitic thread pairs gall easily under frictional heating. Always apply anti-seize and follow the Wax/PTFE/Anti-seize column (K≈0.10).
Scope & limits
- This chart is a simplified K-factor estimate, not a full VDI 2230 analysis (which accounts for joint resilience, embedment and assembly method).
- Friction is the dominant variable — no single torque value exists without its friction state.
- Always follow the design specification or manufacturer torque table.
Cite this chart
YAXIIO. M6 Bolt Torque Chart: Specs, Values & Settings. https://www.yaxiio.com/en/tools/bolt-torque-chart/m6 (accessed 2026-10-29).
Free to cite and embed — attribution required: “YAXIIO” + a link to this page.
FAQ
What is the target preload for an M6 bolt?
At 70% of Rp0.2: class 4.8 ≈ 4.8 kN, 8.8 ≈ 9 kN, 10.9 ≈ 13.2 kN; stainless A2-70 ≈ 6.3 kN and A4-80 ≈ 8.4 kN.
Can I use carbon-steel torque values for stainless M6 (A2-70/A4-80)?
No. The classes have different yield strengths (A2-70 = 450 MPa, A4-80 = 600 MPa), so target preloads differ; and stainless thread pairs gall easily — always apply anti-seize and follow the Wax/PTFE/Anti-seize column (K≈0.10).
Next: work out your order, or pick the size by standard
Related References
Bolt Torque Calculator
Interactive version: fine threads, imperial, stud bolts, custom K and torque check — this size is pre-filled.
M6 Hex Bolt Weight Chart
Per-piece and per-1,000-pcs weights across the full length series of the same size.
M6 Hex Key Size Chart
Which hex key (Allen wrench) fits a socket head cap screw of the same size: socket width across flats, key long and short arm lengths, and unit weight on the GB/T 70.1 + GB/T 5356 basis.
Tap Drill for the Thread Being Tightened
The hole under the bolt: rule tap drill value plus the nearest drill bit in the set, stated ahead of the torque tables.
Disclaimer: This chart is an engineering estimation for selection and budgeting only. It does not constitute assembly instructions or acceptance criteria.