Engineering reference on fasteners and hardware, written by a team with manufacturing backgrounds.

About this site →

Engineering Tools · Wrench and Socket Openings

M20 Bolt Wrench Size: 30 mm Wrench and Socket Opening

M20 Width Across Flats, Side by Side

Four rows, one size. Each row gives the value its governing standard sets and the opening it maps to. The tool opening you need is the width across flats of the part you actually turn - for a hex head bolt that is s, for a hex nut that is s, for a flange nut that is s. The carriage bolt row is different in kind: its square neck is not a hex and no wrench goes on it (it bites into the slot and stops the bolt turning), so tighten on the nut side; it is listed because it is the dimension most often asked about alongside the others for the same nominal size.

Fastener / featureWidth across flats s (mm)Wrench / socket opening (nominal)Standard (row-level source)
Hex head bolt30 mm30 mm (1 3/16″)ISO 4014 / GB/T 5782-2025
Hex nut30 mm30 mm (1 3/16″)ISO 4032 / GB/T 6170-2015
Flange nut30 mm30 mm (1 3/16″)ISO 4161 / GB/T 6177.1-2016 (type 2)
Carriage bolt square neck20.52 mmnot a wrench opening - tighten on the nut sideDIN 603 / ISO 8677 / GB/T 12-2013

A dash means this chart has no value for that combination: the flange nut data behind this page covers M6, M8, M10, M12, M16 and M20, and the carriage bolt data covers M6-M20 except M18. A missing size is not interpolated or extrapolated - ask us for the drawing-level figure. Widths across flats here are nominal; the real fit also depends on the fastener tolerance and on the tool's own tolerance band.

Full PDF

Download the full PDF (M6–M36, all sizes)

Printable chart covering every size in this family — enter your email to get it.

Other Sizes

All Sizes: M6-M36 Wrench and Socket Openings

The same four columns across the whole range, one row per size. The wrench/socket column is the hex bolt width across flats with its nearest imperial fraction in brackets (a nominal label, not a conversion - see the notes under the table). Use it to find the tool for a bolt you already have, or to compare what a nut, a flange nut or a carriage bolt of the same size will need.

SizeHex bolt s (mm)Wrench / socket (nominal)Hex nut s (mm)Flange nut s (mm)Carriage bolt neck s (mm)
M610 mm10 mm (3/8″)10 mm10 mm6.3 mm
M813 mm13 mm (1/2″)13 mm13 mm8.36 mm
M1016 mm16 mm (5/8″)16 mm15 mm10.36 mm
M1218 mm18 mm (11/16″)18 mm18 mm12.43 mm
M1421 mm21 mm (13/16″)21 mm—14.43 mm
M1624 mm24 mm (15/16″)24 mm24 mm16.43 mm
M1827 mm27 mm (1 1/16″)27 mm——
M2030 mm30 mm (1 3/16″)30 mm30 mm20.52 mm
M2232 mm32 mm (1 1/4″)34 mm——
M2436 mm36 mm (1 7/16″)36 mm——
M2741 mm41 mm (1 5/8″)41 mm——
M3046 mm46 mm (1 13/16″)46 mm——
M3350 mm50 mm (1 15/16″)50 mm——
M3655 mm55 mm (2 3/16″)55 mm——

A dash means this chart has no value for that combination: the flange nut data behind this page covers M6, M8, M10, M12, M16 and M20, and the carriage bolt data covers M6-M20 except M18. A missing size is not interpolated or extrapolated - ask us for the drawing-level figure. Widths across flats here are nominal; the real fit also depends on the fastener tolerance and on the tool's own tolerance band.

Heavy Hex and Other Series: Why Charts Give Different Numbers

Heavy hex fasteners (the heavy series in the ASME B18.2.1 / B18.2.6 family, and the high-strength structural series) use a larger width across flats than the regular hex series at the same nominal diameter. If you measure a head or nut that has been called "M12" and get a noticeably larger opening than the value in the table above, that is the tell. A wrench that fits the regular hex series will not fit the heavy hex series, and the two are not interchangeable in the same joint. This chart does not tabulate heavy hex: the ISO/GB series it is built on has no heavy hex column, so take those values from ASME B18.2.1 / B18.2.6 or the drawing. Order those items against the drawing or the standard the buyer names.

The second reason shop charts disagree is the size series. Two bases are in circulation for the same nominal diameter: the reduced across-flats series used here (ISO 4014 / GB/T 5782 for bolts, ISO 4032 / GB/T 6170 for nuts - M10 16 mm, M12 18 mm, M14 21 mm) and the withdrawn German DIN 933 / DIN 934 series, which is one step larger at exactly those three sizes (17 / 19 / 22 mm). The widely repeated line "an M12 bolt takes a 19 mm wrench" is the DIN basis; on the ISO/GB basis used throughout this page an M12 bolt takes an 18 mm wrench. Each is correct for its own basis, and what decides is which one your drawing or contract names - so check the basis before you buy a tool or a box of fasteners.

Data Basis and Assumptions Disclosed

Data basis

  • Every value on this page is derived at render time from fastenerCalc — the same library that drives the calculators and the weight charts on this site.
  • The bolt row reads SIZES[].hexHead.s (ISO 4014 / GB/T 5782), the nut row SIZES[].hexNut.s (ISO 4032 / GB/T 6170), the flange nut row FN_DIMS (GB/T 6177.1-2016 type 2) and the carriage bolt row CB_DIMS (GB/T 12-2013); the row-level standards are named in the table itself.
  • No heavy hex column is published; imperial fractions are nominal nearest-1/16″ labels — neither an inch-size chart nor an exact conversion.

Scope & limits

  • Widths across flats are nominal values; actual parts vary within tolerance and the fit also depends on the tool tolerance — this page is not an acceptance basis.
  • Imperial fractions are the nearest sixteenth by rounding, meant to help you find the closest tool at hand, not as a conversion (13 mm is not 1/2 in).
  • Combinations shown as a dash have no value in this chart’s data and are deliberately not interpolated.
  • Everything here is on the ISO/GB series, which differs from the withdrawn DIN 933 / DIN 934 series at M10, M12 and M14 — confirm the basis on your drawing before ordering tools or fasteners.

Cite this chart

YAXIIO. M20 Bolt Wrench Size: 30 mm Wrench and Socket Opening. https://www.yaxiio.com/en/tools/wrench-size-chart/m20 (accessed 2026-11-17).

Free to cite and embed — attribution required: “YAXIIO” + a link to this page.

FAQ

Charts disagree for M20 - which number is right?

Both can be right, because two series are in circulation for the same nominal diameter. This page uses the reduced across-flats series (ISO 4014 / GB/T 5782 for bolts, ISO 4032 / GB/T 6170 for nuts): M10 16 mm, M12 18 mm, M14 21 mm. The withdrawn German DIN 933 / DIN 934 series is one step larger at exactly those three sizes - M10 17 mm, M12 19 mm, M14 22 mm - and that is where the widely repeated "M12 takes a 19 mm wrench" comes from. For M20 this page gives 30 mm on the ISO/GB basis. Neither number is wrong in itself; the basis named on your drawing or contract decides which one applies.

Do a bolt and its matching nut need the same wrench size?

Usually, and you can check it row by row above. On the bases used here the bolt and the hex nut match at every size in the table except M22, where the bolt is 32 mm across flats while the ISO 4032 / GB/T 6170 nut is 34 mm - so an M22 nut needs one step larger than the bolt itself. Flange nuts are a separate case again: they can be one step smaller than the plain hex nut of the same size (M10: 15 mm against 16 mm on the GB/T 6177.1 type 2 series). Read the row for the part you are actually turning instead of assuming the bolt size carries over.

Will an imperial socket fit a metric bolt?

Close, but treat it as a fallback rather than a substitute. Only a few nominal sizes sit near each other (13 mm against 1/2 in = 12.7 mm; 19 mm against 3/4 in = 19.05 mm), and even a close pair carries visible play. The fractional label in the table is the nearest sixteenth by rounding: it tells you which imperial socket is closest, not that the two are interchangeable. On a tight or already damaged fastener, or with a worn tool, use the metric size by name and keep the imperial one for emergencies at low torque.

Can I use the same wrench on a heavy hex bolt or nut?

No. Heavy hex fasteners (the heavy series in the ASME B18.2.1 / B18.2.6 family, and the high-strength structural series) are larger across flats than the regular hex series at the same nominal diameter, so a wrench that fits a regular hex item will not fit the heavy hex one, and the two are not interchangeable in a joint either. This chart does not publish heavy hex values: the ISO/GB data it is built on has no heavy hex column, so take them from ASME B18.2.1 / B18.2.6 or the drawing. Order those to the drawing or the standard the buyer names, and confirm the across-flats figure by measurement.

Related References

Disclaimer: This table is engineering reference data for tool selection, ordering and fit checking only, not a design basis or acceptance standard.