Consolidating a Mixed Fastener List: Where Substitution Turns Into Risk
25 min·Yaxiio Engineering Alliance

Consolidating a Mixed Fastener List: Where Substitution Turns Into Risk

Which fastener lines can share one export order, which must stay apart, and how to keep heat traceability when sizes, classes and coatings are consolidated.

When Forty Lines Become One Order

A project closes with forty fastener lines still open: M12 to M24, classes 8.8 and 10.9, zinc plated and hot-dip galvanized, coarse and fine thread, lengths from 20 to 180 mm. Purchasing wants one order. Some lines can be combined; others cannot share a carton without changing what the parts do.

Size is visible; class and coating are marked, though heavy coating can hide the mark. The lot is invisible once the parts leave the box. Merges that pass a visual check fail at the wrench or in a recall.

  • Same diameter, class, coating and lot, different lengths: merge, separate inner packs.
  • Same coating and lot, different diameters: one outer carton, separate sealed inner packs.
  • Different class, coating family, hot-dip against thin coating, or thread tolerance band: keep apart.

Four Attributes Decide Whether Two Lines Merge

A fastener line carries four attributes: size (diameter, length, full or partial thread), property class, coating or surface state, and thread (series, pitch, tolerance band). Two lines are the same part only when all four agree.

Attribute May differ inside one order Verdict
Length 50, 60 and 70 mm at one diameter, class, coating and lot Allowed
Diameter M12 and M16 in one outer carton, same coating and lot Packaging only
Property class 8.8 and 10.9 at one size Prohibited
Coating family Zinc plated and zinc flake, or hot-dip and electroplated Prohibited
Thread Coarse against fine, 6g against 6e, 6H against 6AZ Prohibited
Lot Two heats, treatment lots or coating lots Label required

Four Combinations That Must Not Merge

A Class Is a Strength Pair, Not a Grade

GB/T 3098.1-2010 §5 defines a property class as two numbers: nominal tensile strength divided by 100, and the yield ratio times ten. At M16, 8.8 is 800/640 MPa and 10.9 is 1,040/940 MPa, tensile and proof minimums (§7.1, Table 3).

A joint designed at 70% of the 10.9 minimum tensile strength, a common convention, is at 728 MPa. An 8.8 bolt in that box reaches 728 MPa against a 640 MPa minimum proof stress, about 14% over: it yields, preload stops rising, and the joint behaves as bearing. Classes 10.9 and 12.9 fall into hydrogen embrittlement classes B and C under GB/T 5267.1-2023 §6, and class C requires baking at a set temperature and time; a 10.9 part in an 8.8 carton carries a certificate that says nothing about it. Nuts follow the bolt: GB/T 3098.2-2015 §4 pairs 8 with 8.8 and 10 with 10.9, and §5 lets a higher nut grade replace a lower one, not the reverse.

Two Coatings Can Look Alike and Load Differently

Torque is T = K · F · d, and K carries thread and bearing friction. Take K = 0.16 for dry zinc plated and 0.20 for waxed zinc flake, to be measured on the batch: at one torque the preload differs by 0.20/0.16 - 1 = 25%.

GB/T 5267.1-2023 §5.3 makes coating thickness and thread assemblability a per-batch test for electroplated parts. GB/T 13912-2020 Table 4 sets 40 μm local and 50 μm average minimum for centrifuged hot-dip threaded parts over 6 mm. A 50 μm hot-dip layer and a 9 μm electroplated layer, the most the g position accepts at P = 2 (Annex D), are not two readings on one scale.

Hot-Dip Zinc Changes the Thread, Not Only the Surface

Hot-dip coating consumes the thread allowance. GB/T 5267.1-2023 Annex D gives the relation: coating thickness t raises the pitch diameter by 4t, and at P = 2 (M14 and M16) the g position accepts at most 9 μm, f 13 μm, e 17 μm. At 50 μm that geometry moves the pitch diameter about 200 μm, far outside 6g. Hot-dip nuts therefore use a positive deviation, 6AZ or 6AX; GB/T 3098.2-2015 §5 warns that this can reduce stripping strength. A 6g bolt and a 6AZ nut are a pair: an electroplated 6H nut will not start on a hot-dip bolt, and a 6AZ nut on a 6g bolt starts with clearance the joint was not designed for; either one becomes site rework.

The Tolerance Band and Thread Form Are Part of the Part

FED-STD-H28/21B-1984 §5.1.1 makes 6g the standard external class and 6H the internal class for metric threads; §1.2.1 ties that pair to the role of inch 2A/2B. A 6e or 6f bolt is a different part from a 6g bolt even when both are called M16.

M16×2 and M16×1.5 have different stress areas and nuts. Partial and full thread are different products: GB/T 5782-2025 §3 sets b ≈ 2d + 6 for l ≤ 125 mm and b ≈ 2d + 12 for 125 < l ≤ 200 mm, while GB/T 5783-2025 §5 gives b = l - a. M16×60 without the product standard names neither.

Where a Merge Is Legitimate

Two merges are safe when the four attributes match.

Same diameter, class, coating and lot, different lengths. M16×50 and M16×60 from one heat, treatment lot and coating lot can ship as one line with two inner packs, each keeping its own marking, count and label. Check the thread band: b moves from 2d + 6 to 2d + 12 at l = 125 mm, so a 120 mm and a 130 mm bolt differ in unthreaded shank by 4 mm, not 10 mm.

Same coating and lot, different diameters. M12, M16 and M20 can share an outer carton with dividers, each inner pack sealed and labelled. The carton is a shipping unit; the inner pack is the traceable unit.

Same batch has three parts: one heat (one melt, one chemistry), one treatment lot (one furnace cycle, one set of mechanical results) and one coating lot (one bath or barrel, one centrifuge charge, one thickness sample). A merge across any of them keeps the parts interchangeable and splits the evidence: allowed with a map, not with one lot code on the box.

Marking That Survives the Carton

GB/T 90.2-2002 §3 requires product marking as the product standard defines it and treats the manufacturer’s identification mark as a standardized mark. §9 requires seven items on every box, bag or carton: manufacturer or distributor name; product name; the marking specified by the product standard; quantity or net weight; date of manufacture or dispatch; quality mark; and any mark required by a standard, carrier or buyer. The label must be correct, legible, complete and firm, and must not fade or peel. §4 sets a six-month no-rust expectation under normal transport and storage.

The unit opened at site must stay identifiable. If an inner bag is opened while the carton stays in the store, the bag needs at least the standard marking, the quantity and a lot code leading to the map. Head marks do not replace this: in practice, a heavy zinc layer can fill a shallow class mark. GB/T 6170-2015 §5 uses the simplified GB/T 1237 marking; the order still adds class and coating.

The Traceability Map and the Reverse Lookup

One table per order, one row per inner pack: the only place where the commercial line and the production lot meet.

Pack Contents Heat no. Treatment lot Coating lot Qty Label code Certificate
P-01 M16×50, 8.8, HDG H-2409-17 HT-2409-B ZN-2410-03 1,200 16-50-88-Z-01 3.1 / H-2409-17
P-02 M16×60, 8.8, HDG H-2409-17 HT-2409-B ZN-2410-03 800 16-60-88-Z-01 3.1 / H-2409-17
P-03 M16×60, 8.8, HDG H-2410-04 HT-2410-A ZN-2410-03 600 16-60-88-Z-02 3.1 / H-2410-04
P-04 M12×40, 8.8, HDG H-2410-04 HT-2410-A ZN-2410-03 2,000 12-40-88-Z-01 3.1 / H-2410-04

Codes are illustrative; labels must work without the table.

  1. Read the head mark and the inner label. If they disagree, quarantine the pack.
  2. Take the lot code to the map row.
  3. Read heat, treatment lot and coating lot.
  4. Pull the certificate and test report for those identifiers, and check the measured values against the class on the label: GB/T 3098.1-2010 §7.1 and Table 3 for bolts, GB/T 3098.2-2015 for nuts.
  5. List every pack sharing any one identifier. That list is the recall scope.

Without the table, step 5 has no answer and the whole shipment is the recall scope.

Counting by Weight or by Piece

GB/T 90.2-2002 §9 puts quantity or net weight on the label. Both comply, but a weight line fixes kilograms while the count follows from a mean piece mass the drawing does not fix.

Formula
m≈ρ · [ (π/4) · d_s² · l+(√3/2) · s² · k ]
N=W/m
ΔN/N≈-Δm/m

m is one bolt’s mass in grams, ρ the steel density (7.85 g/cm³, empirical), d_s the shank diameter, l the length under the head, s the width across flats and k the head height; N is the count for a weight W. The third line says the count error is the mass error with the opposite sign.

For M16×60 to GB/T 5782-2025, Table 4 gives d_s 16.00 mm nominal (the maximum), d_s min 15.57 mm, s 24 mm, and k 10.00 mm nominal with 9.71-10.29 mm limits. At 7.85 g/cm³ the nominal mass is 133.9 g; at the low limits 127.7 g; with k at maximum 135.0 g. The geometry is approximate; the spread is not.

Ten thousand pieces weigh between 1,277 kg and 1,350 kg, a 5.7% band. If the order states both 10,000 pieces and 1,338.6 kg, one of the two fails at the limits. Choose one governing quantity, and weigh 50 pieces on a 1 g scale to fix the conversion; the batch spread stays.

Risk Matrix: Allowed, Labelled, Prohibited

Apply the checks in order; the first no ends it.

Dimension Verdict Condition Consequence if ignored
Same diameter, class, coating and lot, different length Allowed Separate inner packs with own count and label Wrong length; thread run-out in the shear plane
Same coating and lot, different diameters Allowed Dividers; sealed inner packs Mixed counts; gauge sample takes the wrong size
Same part, different heat, treatment or coating lot Label required One map row per lot; distinct pack codes Recall scope grows; one result covers parts it never saw
Same size, 8.8 against 10.9 Prohibited None Yield at design preload; baking evidence lost
Same size and class, zinc plated against zinc flake Prohibited None About 25% preload shift at K 0.16 vs 0.20
Hot-dip against any thin coating Prohibited None Thread will not start, or starts loose
Coarse against fine pitch Prohibited None Wrong stress area and nut
6g against 6e or 6f; 6H against 6AZ or 6AX Prohibited None Gauge result depends on the part picked

Label required means the pack shares the shipment, not the bag.

Before You Release the Consolidated Order

Takeaway Checklist
Copy this checklist into your tender documents
Selected conditions
Tap to check, this is your procurement checklist

The consolidated order is also the document used to accept or reject the shipment; the map belongs in the packing list. A carton that cannot be traced to a heat is quarantined whole, though every part inside may be correct. Review the labels against the receiving inspection checklist before unloading.

References

Key Standards

Standards and clauses referenced by this article.

  1. Fasteners: marking and packaging§3, §4, §9

    Product marking and the manufacturer identification mark (§3); six-month no-rust expectation under normal transport and storage (§4); the seven items required on every box, bag or carton and label durability (§9). Values are quoted; the full text is not reproduced.

  2. Mechanical properties of fasteners: bolts, screws and studs§5, §7.1, Table 3

    Property class designation (§5) and minimum values used here: class 8.8 is 800 MPa tensile and 640 MPa proof; class 10.9 is 1,040 MPa and 940 MPa (§7.1, Table 3).

  3. Mechanical properties of fasteners: nuts§4, §5

    Nut grade numbers pair with bolt classes (8 with 8.8, 10 with 10.9); a higher nut grade may replace a lower one, not the reverse; a positive basic deviation such as 6AZ or 6AX can reduce stripping strength.

  4. Hexagon head bolts, partially threaded§3, Table 4

    Thread length b by length band: about 2d+6 for l <= 125 mm and 2d+12 for 125 < l <= 200 mm. The M16 values used in the weight example are ds min 15.57 mm, k 9.71-10.29 mm and s 24 mm.

  5. Hexagon head bolts, fully threaded§3, §5

    Fully threaded product: b = l - a and incomplete thread u <= 2P. Used to show that a call-out such as M16x60 does not identify the product standard on its own.

  6. Fasteners: electroplated coatings§4.4, §5.3, §6, Annex D

    Annex D: coating thickness t raises the pitch diameter by 4t; at P = 2 the g position accepts at most 9 um, f 13 um, e 17 um. §5.3 makes thickness and thread assemblability per-batch tests; §6 places classes 10.9 and 12.9 in hydrogen embrittlement classes B and C.

  7. Hot-dip galvanized coatings on steelTable 4

    Centrifuged hot-dip threaded parts over 6 mm: 40 um local minimum and 50 um average minimum coating thickness.

  8. Hexagon nuts, style 1§5

    Nut marking follows the simplified GB/T 1237 form; class and coating are added by the purchase order.

  9. Screw-Thread Standards for Federal Services, Section 21: Metric Screw Threads§1.2.1, §5.1.1

    Standard metric tolerance classes: 6g external and 6H internal, tied to the role inch 2A/2B plays. No stable public URL was reachable from the review environment; bibliographic entry only.

Deep Reading

More systematic selection, procurement, or inspection guides.

This page is one entry in the fastener engineering reference. The library covers standards, dimensions, materials, and failure analysis; every figure is traced back to its source.

Continue reading in the library →