Engineering reference on fasteners and hardware, written by a team with manufacturing backgrounds.

About this site →

Engineering Tools · Machine Screw Reference

M2 Screw Size Chart: Head Dimensions and Drive Size

M2 in every head type (mm)

One row per head type at the same thread size. dk and k are nominal (= max) values from the standard named in each row.

Head typeStandardHead dia. dk (mm)Head height k (mm)Coarse pitch P (mm)Drive size
Slotted pan head (ISO 1580 / GB/T 67)ISO 1580 / GB/T 67-201641.30.4Slot width n = 0.5 mm
Cross recessed pan head (ISO 7045 / GB/T 818)ISO 7045 / GB/T 818-201641.60.4No.0 (PH0)
Cross recessed countersunk head 90° (ISO 7046-1 / GB/T 819.1)ISO 7046-1 / GB/T 819.1-20163.81.20.4No.0 (PH0)
Cross recessed cheese head (ISO 7048 / GB/T 822)ISO 7048 / GB/T 822-2016————
Socket head cap (ISO 4762 / GB/T 70.1)ISO 4762 / GB/T 70.1-20083.820.4Hex socket s = 1.5 mm

ISO 7048 / GB/T 822 covers M2.5 to M8, so the cheese head row is blank at M1.6, M2 and M10. Use the pan head or socket head column for those sizes.

Head figures are the standard's nominal (= max) values. Head height depends on the head type, so an M5 screw is 3.7 mm high as a cross recessed pan head and 5.0 mm as a socket head cap. Tolerances, property classes and surface finish are agreed on order.

Full PDF

Download the full PDF (M1.6–M10, all sizes)

Printable chart covering every size in this family — enter your email to get it.

Other sizes

Machine screw size chart, M1.6–M10 (mm)

Pick a head type. dk is the head diameter and k the head height, both on the standard's nominal (= max) basis. "Recess No." is the cross recess size No.0 to No.4, which is the same as a PH0 to PH4 bit; a slotted head has a slot width n instead, and a socket head has a hexagon socket s.

Head type

Cross recessed pan head (ISO 7045 / GB/T 818) · ISO 7045 / GB/T 818-2016

Size d (mm)Coarse pitch P (mm)Head dia. dk (mm)Head height k (mm)Recess No.
M1.60.353.21.30
M20.441.60
M2.50.4552.11
M30.55.62.41
M40.783.12
M50.89.53.72
M61124.63
M81.251664
M101.5207.54

The recess No. is the bit: No.0 to No.4 is a PH0 to PH4 bit. Recess numbering is per head type, so the same thread size can take a different recess number in two head types.

M2 beside the next sizes

In this range the nominal diameter steps by 0.5 mm or 1 mm. Measure d across the thread with a caliper and compare with the rows below before ordering.

Left four columns: cross recessed pan head (ISO 7045 / GB/T 818). Right four columns: socket head cap (ISO 4762 / GB/T 70.1). Values in mm, nominal (= max).

Size d (mm)Coarse pitch P (mm)Head dia. dk (mm)Head height k (mm)Recess No.Head dia. dk (mm)Head height k (mm)Hex socket s (mm)
M1.6d = 1.60.353.21.3031.61.5
M2d = 20.441.603.821.5
M2.5d = 2.50.4552.114.52.52

Which dimension do you need? d, dk, k and the drive size

A machine screw carries four different numbers that all get called "the size". Buyers order by the first one and measure the others, which is where most wrong orders start.

d - nominal thread diameter

The number after M: M5 is d = 5 mm, a 5 mm thread. It is what the order is placed on, and it is not the head size.

P - pitch

Distance between two thread crests. M5 in the coarse series is 0.8 mm. Coarse pitch covers almost all machine screws; fine pitch is agreed on order against the drawing.

dk - head diameter

Outside diameter of the head, measured across it with a caliper. It sets the clearance hole and the counterbore: 4 mm for an M5 cross recessed pan head, — mm for an M5 cheese head, 3.8 mm for an M5 countersunk head.

k - head height

Height of the head above the bearing surface (on a countersunk head this is kc, the depth that has to be sunk). It sets counterbore depth and how far the head stands proud: 1.6 mm for an M5 pan head, 2 mm for an M5 socket head, 1.2 mm for an M5 countersunk head.

Drive size - recess No., slot width n or hexagon socket s

The recess that takes the tool: No.0 (PH0) at M5 in the cross recessed pan head series, slot width n = 0.5 mm at M5 in the slotted series, hexagon socket s = 1.5 mm at M5 for a socket head cap screw. Take the drive size from the head type, not from the thread size.

Metric to inch machine screw sizes (approximate, not interchangeable)

Cross-reference by nominal diameter only. The inch column is a straight millimetre-to-inch conversion of d; the last column is the inch machine screw whose nominal diameter is closest to it.

Metric sizeNominal d (mm)Nominal d (in)Closest inch machine screw
M220.079#1 (1.854 mm)

matched by nominal diameter only

Do not substitute. Metric and inch machine screws both use a 60° thread form, but the diameters and thread counts differ, so a near-diameter inch screw starts and then jams and damages the thread. Use these rows to read which callout a drawing means, not to interchange parts.

Cite this chart

YAXIIO. {size} Screw Size Chart: Head Dimensions and Drive Size. https://www.yaxiio.com/en/tools/screw-size-chart/m2 (accessed 2026-11-17).

Free to cite and embed — attribution required: “YAXIIO” + a link to this page.

FAQ

Is the M number the head size on an M2 machine screw?

No. The number after M is the nominal thread diameter d: an M2 screw is d = 2 mm across the thread, while the head is wider - dk = 4 mm on a cross recessed pan head and 3.8 mm on a socket head cap screw. Order by the M number, and confirm dk and k against the drawing or the counterbore.

Countersunk or pan head M2 - which do I need?

Countersunk sits flush and needs a machined 90° seat: the M2 countersunk head is dk = 3.8 mm, with a theoretical dk max of 4.4 mm for the seat and kc = 1.2 mm of head to sink. Pan head sits on the surface and needs no seat: the M2 pan head is dk = 4 mm and stands k = 1.6 mm proud. Use countersunk where the head must not protrude, and pan head where a bearing surface or easy removal matters.

Can I replace an M2 metric screw with an inch screw?

No, not as a substitute. The M2 thread is d = 2 mm with a 0.4 mm pitch, and the nearest inch machine screw only matches the diameter to within a few tenths of a millimetre while carrying a different thread count - so it will not run true in the same nut or tapped hole and will damage it. Both series are 60° threads, so the two look close on a drawing; cross-reference them to read callouts, and order the thread the joint is made for.

Related References

Disclaimer: this table is a selection and quotation reference built from the standard editions named on this page, not a design basis or an acceptance standard.