Engineering reference on fasteners and hardware, written by a team with manufacturing backgrounds.

About this site →

Engineering Tools · Machine Screw Reference

M2.5 Screw Size Chart: Head Dimensions and Drive Size

M2.5 in every head type (mm)

One row per head type at the same thread size. dk and k are nominal (= max) values from the standard named in each row.

Head typeStandardHead dia. dk (mm)Head height k (mm)Coarse pitch P (mm)Drive size
Slotted pan head (ISO 1580 / GB/T 67)ISO 1580 / GB/T 67-201651.50.45Slot width n = 0.6 mm
Cross recessed pan head (ISO 7045 / GB/T 818)ISO 7045 / GB/T 818-201652.10.45No.1 (PH1)
Cross recessed countersunk head 90° (ISO 7046-1 / GB/T 819.1)ISO 7046-1 / GB/T 819.1-20164.71.50.45No.1 (PH1)
Cross recessed cheese head (ISO 7048 / GB/T 822)ISO 7048 / GB/T 822-20164.51.80.45No.1 (PH1)
Socket head cap (ISO 4762 / GB/T 70.1)ISO 4762 / GB/T 70.1-20084.52.50.45Hex socket s = 2 mm

Head figures are the standard's nominal (= max) values. Head height depends on the head type, so an M5 screw is 3.7 mm high as a cross recessed pan head and 5.0 mm as a socket head cap. Tolerances, property classes and surface finish are agreed on order.

Full PDF

Download the full PDF (M1.6–M10, all sizes)

Printable chart covering every size in this family — enter your email to get it.

Other sizes

Machine screw size chart, M1.6–M10 (mm)

Pick a head type. dk is the head diameter and k the head height, both on the standard's nominal (= max) basis. "Recess No." is the cross recess size No.0 to No.4, which is the same as a PH0 to PH4 bit; a slotted head has a slot width n instead, and a socket head has a hexagon socket s.

Head type

Cross recessed pan head (ISO 7045 / GB/T 818) · ISO 7045 / GB/T 818-2016

Size d (mm)Coarse pitch P (mm)Head dia. dk (mm)Head height k (mm)Recess No.
M1.60.353.21.30
M20.441.60
M2.50.4552.11
M30.55.62.41
M40.783.12
M50.89.53.72
M61124.63
M81.251664
M101.5207.54

The recess No. is the bit: No.0 to No.4 is a PH0 to PH4 bit. Recess numbering is per head type, so the same thread size can take a different recess number in two head types.

M2.5 beside the next sizes

In this range the nominal diameter steps by 0.5 mm or 1 mm. Measure d across the thread with a caliper and compare with the rows below before ordering.

Left four columns: cross recessed pan head (ISO 7045 / GB/T 818). Right four columns: socket head cap (ISO 4762 / GB/T 70.1). Values in mm, nominal (= max).

Size d (mm)Coarse pitch P (mm)Head dia. dk (mm)Head height k (mm)Recess No.Head dia. dk (mm)Head height k (mm)Hex socket s (mm)
M2d = 20.441.603.821.5
M2.5d = 2.50.4552.114.52.52
M3d = 30.55.62.415.532.5

Which dimension do you need? d, dk, k and the drive size

A machine screw carries four different numbers that all get called "the size". Buyers order by the first one and measure the others, which is where most wrong orders start.

d - nominal thread diameter

The number after M: M5 is d = 5 mm, a 5 mm thread. It is what the order is placed on, and it is not the head size.

P - pitch

Distance between two thread crests. M5 in the coarse series is 0.8 mm. Coarse pitch covers almost all machine screws; fine pitch is agreed on order against the drawing.

dk - head diameter

Outside diameter of the head, measured across it with a caliper. It sets the clearance hole and the counterbore: 5 mm for an M5 cross recessed pan head, 4.5 mm for an M5 cheese head, 4.7 mm for an M5 countersunk head.

k - head height

Height of the head above the bearing surface (on a countersunk head this is kc, the depth that has to be sunk). It sets counterbore depth and how far the head stands proud: 2.1 mm for an M5 pan head, 2.5 mm for an M5 socket head, 1.5 mm for an M5 countersunk head.

Drive size - recess No., slot width n or hexagon socket s

The recess that takes the tool: No.1 (PH1) at M5 in the cross recessed pan head series, slot width n = 0.6 mm at M5 in the slotted series, hexagon socket s = 2 mm at M5 for a socket head cap screw. Take the drive size from the head type, not from the thread size.

Metric to inch machine screw sizes (approximate, not interchangeable)

Cross-reference by nominal diameter only. The inch column is a straight millimetre-to-inch conversion of d; the last column is the inch machine screw whose nominal diameter is closest to it.

Metric sizeNominal d (mm)Nominal d (in)Closest inch machine screw
M2.52.50.098#3 (2.515 mm)

matched by nominal diameter only

Do not substitute. Metric and inch machine screws both use a 60° thread form, but the diameters and thread counts differ, so a near-diameter inch screw starts and then jams and damages the thread. Use these rows to read which callout a drawing means, not to interchange parts.

Cite this chart

YAXIIO. {size} Screw Size Chart: Head Dimensions and Drive Size. https://www.yaxiio.com/en/tools/screw-size-chart/m2-5 (accessed 2026-11-17).

Free to cite and embed — attribution required: “YAXIIO” + a link to this page.

FAQ

Is the M number the head size on an M2.5 machine screw?

No. The number after M is the nominal thread diameter d: an M2.5 screw is d = 2.5 mm across the thread, while the head is wider - dk = 5 mm on a cross recessed pan head and 4.5 mm on a socket head cap screw. Order by the M number, and confirm dk and k against the drawing or the counterbore.

Countersunk or pan head M2.5 - which do I need?

Countersunk sits flush and needs a machined 90° seat: the M2.5 countersunk head is dk = 4.7 mm, with a theoretical dk max of 5.5 mm for the seat and kc = 1.5 mm of head to sink. Pan head sits on the surface and needs no seat: the M2.5 pan head is dk = 5 mm and stands k = 2.1 mm proud. Use countersunk where the head must not protrude, and pan head where a bearing surface or easy removal matters.

Can I replace an M2.5 metric screw with an inch screw?

No, not as a substitute. The M2.5 thread is d = 2.5 mm with a 0.45 mm pitch, and the nearest inch machine screw only matches the diameter to within a few tenths of a millimetre while carrying a different thread count - so it will not run true in the same nut or tapped hole and will damage it. Both series are 60° threads, so the two look close on a drawing; cross-reference them to read callouts, and order the thread the joint is made for.

Related References

Disclaimer: this table is a selection and quotation reference built from the standard editions named on this page, not a design basis or an acceptance standard.