Engineering reference on fasteners and hardware, written by a team with manufacturing backgrounds.

About this site →

ENGINEERING TOOL

Flat & Spring Washer Weight Chart (M6–M36) — DIN 125 A / GB/T 97.1-2002 · DIN 127

SizeD (mm)t (mm)Unit weight (g)
±2%
kg per 1,000 pcs (approx.)
M6121.61.02 g1.016
M8161.61.83 g1.829
M102023.57 g3.573
M12242.56.27 g6.273
M1630311.3 g11.3
M2037317.2 g17.2

Unit weight and weight per 1,000 pcs for all 14 metric sizes of plain (flat) washers and spring lock washers side by side, computed as geometric volume × density on carbon steel — same formula and parameters as the weight calculator and the per-size charts, with the basis disclosed right below the tables and estimate tolerances of ±2% for flat washers and ±10% for spring washers.

Full PDF

Download the full PDF (M6–M36, all sizes)

Printable chart covering every size in this family — enter your email to get it.

Full Size Tables (M6–M36)

Click a size for its dedicated chart (material density conversion card and kg/1000 pcs ↔ lb/100 pcs toggle). D = outside diameter, t = thickness.

Plain Washers (ISO 7089 ≈ GB/T 97.1, DIN 125 A bore)

SizeD (mm)t (mm)Unit weight (g)
±2%
kg per 1,000 pcs (approx.)
M6121.61.02 g1.016
M8161.61.83 g1.829
M102023.57 g3.573
M12242.56.27 g6.273
M14282.58.62 g8.616
M1630311.3 g11.3
M1834314.7 g14.7
M2037317.2 g17.2
M2239318.3 g18.3
M2444432.3 g32.3
M2750442.3 g42.3
M3056453.6 g53.6
M3360575.3 g75.3
M3666592.1 g92.1

Spring Lock Washers (DIN 127 series, modeled dims)

SizeD (mm)t (mm)Unit weight (g)
±10%
kg per 1,000 pcs (approx.)
M611.81.60.85 g0.845
M814.821.59 g1.587
M1018.12.22.56 g2.562
M1221.12.53.85 g3.853
M1424.135.91 g5.908
M1627.43.58.86 g8.861
M1830.43.510.7 g10.7
M2033.5414.8 g14.8
M2235.5415.9 g15.9
M2439524.2 g24.2
M2744530.9 g30.9
M3049646.1 g46.1
M3353652.8 g52.8
M3657660 g60

Basis of Calculation & Disclosed Assumptions

Calculation basis

  • Both tables are computed as annular geometric volume × density (carbon steel 7.85 g/cm³, base metal, coating excluded) — identical formula and parameters as the online weight calculator and the per-size charts.
  • Plain washers use π/4·(D²−d1²)·t with the bore at the DIN 125 A standard hole diameter d1 (slightly larger than the nominal thread diameter, so no separate ID column is shown); on this basis the 14 sizes stay within 0.3% of published DIN 125 per-1,000-pcs weights, and the page tolerance is set to ±2% to leave room for production thickness tolerance.
  • Spring lock washers use π/4·(D²−d²)·t (bore at the nominal diameter d) with an effective-section factor for the split gap and section chamfers, regressed on published DIN 127 per-1,000-pcs weights — a coarser model, so the page uses the more conservative ±10%.

Scope & limits

  • Theoretical geometric estimates for quotation, freight and packing budgets; use measured values for trade settlement.
  • Actual piece weight varies with thickness tolerance, chamfer, split-ring geometry and coating (hot-dip galvanizing ≈ +4.5%).
  • Estimate tolerance: ±2% for plain washers, ±10% for spring lock washers.

Other materials, other sizes? Use the calculator

The weight calculator covers flat washers and spring washers at any size with stainless and brass density conversion — piece, batch and pieces-per-tonne results in one pass.

Open the weight calculator

Cite this chart

YAXIIO. Flat & Spring Washer Weight Chart (M6–M36) — DIN 125 A / GB/T 97.1-2002 · DIN 127. https://www.yaxiio.com/en/tools/flat-washer-weight-chart (accessed 2026-11-17).

Free to cite and embed — attribution required: “YAXIIO” + a link to this page.

FAQ

Why does the same size show two different washer weights?

Because they are two different products. A plain washer is a solid annular ring that spreads the bolt load over the mating surface; a spring lock washer is a split ring whose ends are offset out of the ring plane, so only part of the ring section carries metal and the weight cannot be read across from the flat-washer column. When a drawing just says "washer", check which of the two is meant — most assemblies use both, flat washer first, spring washer on top.

Does this chart cover DIN 9021 / fender washers?

No. This table covers standard-series plain washers (ISO 7089 ≈ GB/T 97.1, DIN 125 A) and DIN 127-series spring lock washers. DIN 9021 (≈ ISO 7093) fender or body washers have a much larger outside diameter — roughly three times the bolt diameter — and are several times heavier, so their weights cannot be derived from this table. If a drawing specifies that series, tell us and we will quote it separately.

How do I convert these carbon-steel values to stainless or brass?

Scale by the density ratio against carbon steel at 7.85 g/cm³: stainless 304 ×1.010, stainless 316 ×1.017, brass ×1.083. Changing the material changes only the density, not the geometry, so the same factor applies to both the plain-washer and the spring-washer columns, and it is equally valid for grams per piece and for kg per 1,000 pcs. The weight calculator outputs other materials directly if you prefer not to multiply by hand.

Related References

Disclaimer: this chart provides engineering estimates for selection, quotation and freight budgeting only; it is not a design basis or an acceptance standard.